VPN

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

VPN connectivity

hi,we are using PIX 506 version 6.3 for our network. We have to do static NAT for the VPN connectivity with the client server. But when i try doing PAT i am not able to connect to the remote server. Can anyone help me out why this is happening.Is tha...

VPN issue with cable modem

I work from Australia for a US based company and I connect via VPN into my company network. I have recently put in a cable modem at home. It fails to obtain an IP address when the VPN is operating. This seems to be because the cable traffic is bei...

rmo by Beginner
  • 311 Views
  • 1 replies
  • 0 Helpful votes

WebVPN & Outlook Web Access

This is likely covered here elsewhere, but I could not locate any references to it.I have just configured WebVPN on a 3005 running 4.1.3. I have configured two links on the WebVPN page. An inside intranet server, and the Exchange (Outlook Web Access...

dheinen by Beginner
  • 1437 Views
  • 8 replies
  • 0 Helpful votes

PIX to PIX and Group VPN

As I stated in my earlier post I have 3 remote offices (PIX 501's) connecting back to my main office where I am running a PIX 506 with IPSEC tunnels connecting the 4 offices.I had an office lose thier 501 PIX to a roof leak and hence that office was ...

slarabee by Beginner
  • 258 Views
  • 1 replies
  • 0 Helpful votes

1721 + ADSL WIC VPN Config?

Hi there, anyone have, or know where I can obtain, a sample config for a 1721 router (IpSec IOS) to allow it to terminate an IPSec tunnel in a remote-access config?thanks,Gary

0r8it by Beginner
  • 266 Views
  • 2 replies
  • 0 Helpful votes

Resolved! PIX 506e VPN pass through to windows VPN server

Title says most of it.I had an 831, and I only needed to port forward the pptp tcp port, 1723 to my Windows 2003 VPN server.Got pix 506e up 2 days ago, and I can't figure out how to get it to pass the traffic. Obviously tcp 1723 is statically mapped....

wjarok by Beginner
  • 399 Views
  • 2 replies
  • 0 Helpful votes

Resolved! PIX501 to Cisco VPN client

Hello,I ran through the VPN Wizzard on the Pix Device Manager but I would like to know how to verify my connections are esablished and passing data.Jason

upgrading from a 3005 concentrator to a 3030

is it possible to take the config from the 3005 and upload to the 3030? has anyone done this? what kind of problems can i expect if i do this?basically i want to avoid having to re-enter everything in the new concentrator (mostly lan-to-lan setups a...

srue by Rising star
  • 278 Views
  • 2 replies
  • 0 Helpful votes

Dialup Preformace Issue

I am currently comparing a Windows2000 RAS server to a Cisco dialup solution with a 3825 router, 8port BRI ISDN and 18 MICA Digital Modem card. Preformace testing with a ThinkPad T42 with builtin modem dialing up an ISDN number to the router. Testi...

fwadmin by Beginner
  • 217 Views
  • 1 replies
  • 0 Helpful votes

Same subnet on both ends of VPN

I have a PIX 501 with 6.3 sw.Several VPN's in place already.Need to setup VPN to new site, problem is they use 192.168.1.x subnet, and so do I.Is there a way to setup an alias on the PIX? What about a 2nd NIC in my end point device?Traffic will look ...

wcotis60 by Beginner
  • 216 Views
  • 1 replies
  • 0 Helpful votes

Resolved! PIX ver 7.0 Remote VPN

Can I make my Remote Access VPN users go to a DMZ of the same firewall they're using as NAS, I tried this, my users can go with out a problem to the inside network but when they try to go to a DMZ the syslog display "No route to DMZ_HOST_IP from REMO...

andujar by Beginner
  • 287 Views
  • 3 replies
  • 0 Helpful votes
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers