I see on some docs such as at https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/6500-bgp-pix.html that you must configure NAT in addition to allowing port 179 to allow BGP through a FW. Basically I am just trying to confirm wh...
Hi Guys I am trying to setup a new IPSEC VPN connection between a Cisco ASA 5520 (verion 8.4(4)) and Checkpoint Firewall. I have successfully established IKE and IPSEC phases and I can see tunnel is UP. But I can't see any traffic going through the ...
Greetings all After reading posts similar to this one: https://community.cisco.com/t5/vpn-and-anyconnect/asa-5505-free-inbuilt-anyconnect-licensing/td-p/3316063, I'm left in the same boat but still having questions. Our 5508-X has a value of 4 for An...
Hi Folks, I am trying to establish routing between two Site to Site vpn tunnels, both of which are terminating on the same outside interface of my Cisco ASA. Please find attached Network Diagram for the same. All Firewalls used are Cisco AS...
Hi all I have a problem with a basic hub and spoke FlexVPN configuration I have created. The config was based on a known working config from a virtual lab with Cisco CSR1000v but it doesn't appear to work on physical hardware (Cisco 892FSP) The tunn...
Hi, I recently downloaded Cisco AnyConnect Secure Mobility Client and I am unable to connect and receive messages to check my internet connectivity. I ran DART and I have that information. Can anyone please assist in troubleshooting this connection i...
I have a Cisco 1921 router that I use at our head office to connect to remote offices across the country. The head office uses 172.16.3.0/24 local IP range. All of the remote locations have identical configuration with IP range 192.168.xxx.0/24. A ne...
Hi All,Can i request to give me a favor to solve my NTP testing.I trying to test ntp configuration and setup in lab.I want to configure R1 as NPT Master of R2 and R2 as NPT client of R1 and R2 is NTP master of R3. I also want to authenicate with MD5 ...
Hello all, I require some assistance in converting a split tunnel site to site connection to a full tunnel. I have read multiple posts, articles etc. From what I gather I need to set the crypto acl to source (Local Lan) and destination ANY. Is this c...
Hello everyone,I am pretty new to the network world and I would like to get some help. I would like to set up a redundancy IP sec tunnels between HQ and Branch office.Both sites have ASA and HQ has 2 outside interfaces that connect to ISP1 and ISP2.B...
Hello, We currently have a VPN tunnel with ASA's at each site. It is working correctly as of right now. I would like to add another subnet that exists at our Site A so that I can manage the equipment at Site B that exists on a different subnet. When ...
Hi All, I need some help with configuring VPN. The current VPN configuration works fine without any issues, however, we would like to route all traffic from SITE A to HQ via Site to Site VPN (including Internet traffic). MY proposed configuration...
Hi Guys, I got a request from my customer:He is using Anyconnect authentication AD + OTP (Freeradius) and now he wants to add authentication with machine certificate so only corporate computers are allowed to connect to the VPN and migrate it complet...
Hi Cisco Forms, I'm trying to practice configuring a VPN on an ASR 1001 and I'm having an issue with the Crypto map.I've excepted the EULA and right-to-use to ensure this is active for testing. I've been able to complete all the configurations except...
Hi,I configured my hub and spoke router with dVTI and policy base ip address assing to spoke router.Everything works fine but the IP address of speaking router tunnel don't show in routing table static and i cannot ping the tunnel ip address and then...
