Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Cisco 3802 with Cisco Switches POE
Hello, I hope everyone is doing great. Just wanted to check to see if the 3802 Series Access Points will work with Cisco 3850 Switch Series as well as the Cisco 9300 Series. Thanks
Resolved! Modifying WLAN Session TImeout
Hello All, Hardware: WLC2504 I want to modify the "Session Timeout (secs)" setting located in our Guest WLAN > Advanced > Session Timeout. I just want to increase the timeout value and change nothing else. If I modify only this setting and "Sav...
I recently acquired an air-ap1532E-UXk9 but I do not know how to set it up. Also I don't know the IP address but I looked through the manual and couldn't figure it out. I connected an Ethernet cable to the console port and my computer. How do I acces...
Resolved! WLC3504 + AP1142N
Hi everyone, can I use an Aironet 1142N Access Point with a 3504 Wireless Controller?The 3504 WLC is shipped with firmware 8.5, but the latest release for the AP 1142N is 8.3 Many thanks in advance!
Hi all, Our team has run into a unique issue when trying to test our newly implemented captive portal. Upon testing on Apple/iOS devices, the portal displays with no issue and functions exactly how we would like. It's a different story on Android, ...
Hi everydody!!! I have an one problem, when I just made or reconfigure one SSID and the apply for all APs; all my wireless clients have a disconnect from the wireless network, this is normal???, or I missed an one extra configuration? My features...
Hi, I configured and installed the Cisco Anconnect 4.6, but allways when we initiate the VPN I receive a Windows with mesage Untrusted Server Certificate. How can I install this certificate on Windows Machine for don´t show this mesage again? Tha...
Recently I upgraded wlc 2504 to version 8.5. My new ap2802i version 8.4 will not join. With my old version of wlc 7.6 I could see the access points attempting to join, but now I see nothing. Could I have a conflict with versions of software? So ...
I am setting up a 5520 WLC for the first time, I have set the local credentials and can access this appliance via console. However my credentials aren't working via SSH or WebGui? Logs seem to show AAA-3-ACCTREQ_SEND_FAILED I also cannot synch wit...
I have added my MESH AP's to the map and the MESH links appear on the map as 0 SNR. I can run the link test Parent-> Child and vise-versa and SNR os good. If I go to Monitor->Access Points-><AP Name>-> Link detail, everything is zeroed out. I do h...
Hi All, I am not sure this is the appropriate place to report a bug, but I haven't found any better forum. I use Cisco AnyConnect Secure Mobility Client 4.4.02039 along with its Network Access Manager module. I use Windows 7 64 bit's in-built PPP...
Hi TeamHope you doing well..I need to deploy new 3 x AIR-CAP3702I AP as a standalone AP,i ordered AP with default image (SWAP3700-RCOVRY-K9) and now need to convert it to Autonomous Mode.Please suggest the steps for 3702I conversion.Thanks in Advance...
Hello All I have 3 APs with autonomous software, so i want to connect them as P2MPT via wireless not wired, One as root-bridge and the other non-root-bridge, the non-root-bridge APs connect to switches to brovide their clients with internet connectio...
Hello, I am using Cisco Prime 3.1. I need to set a threshold for AP Utilization. Then, need to generate alarms for when the utilization is above that limit and receive those alarms by e-mail. I've seen that some questions about this issue have been...
Hi, I have an DMZ WLC- 5508 and internal foreign WLC cisco flex 7500 . I configured mobility anchor between these two WLC. I get data path as up and control path to be down. Also between these WLC s firewall is not there. Please help.
