Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello,We have a third controller and we want to move some (300) accesspoints to that controller.But I cannot find in the controller software or in Prime infra (3.4) how to do quickly, without to click on each Accesspoint and move them to that control...
Hi there,I need some help understanding Meraki offerings that would help me get better WiFi performance and overall network security in my house.Situation is as follows- 2 story standard West USA construction (wood frame, drywall), medium size home w...
Hi, I installed 8.1.122 on a WLC and I see a feature that I can't find any documentation on. Under a RF Profile in the RRM tab there is a feature called High-Speed Roam and a checkbox for HSR mode and Neighbor Timeout Factor. What does this do? I hav...
Hi everyone,I am trying to use 802.11w PMF feature for a 802.1x SSID. When I configure it to "Required", supported clients can connect with AKM: 11w-802.1x and unsupported clients cannot connect at all. This scenario works as expected. But when I do ...
We have had an AIR-AP1572EAC-E-K9 installed by a 3rd party but unsure if the alignment is as true as it could be, I’ve been searching Cisco with no luck on how to make sure that these are aligned as good as they can be. Is there a tool that we can us...
Resolved! CCNA wireless prerequisite
Will my valid CCIE Written (400-101) qualify as a valid prerequisite for CCNA Wireless (200-355)?
Hello,i have two C9800-40 Controllers, both installed via image (.bin) in bootflash: via install add command. Now i have one who installed in bootflash:, boot system bootflash:packages.conf and the other one in harddisk:, boot system harddisk:package...
Resolved! Enable 40 Mhz channels for 2.4 Ghz band
Im looking into having 40 Mhz channels over 2.4Ghz band, is there a way to have this enabled? Any suggestions?
Hi All, Recently we bought a 5520-K9 WLC and AP2802I-E-K9 APs, DHCP is configured on the Switch and AP is getting IPbut unable to ping or it is not discoveredplease advise
Resolved! WAP 371 malformed packets in 5Ghz ac
Gents, I have a weird issue with WAP371-E-K9 V01, fw 1.3.0.7In 5Ghz AC mode I capture pcap using "administration" -> "packet capture" and getting a lot of "IEEE 802.11: Malformed Packet (Exception occurred)" and "IEEE 802.11: Tag Length is longer tha...
Resolved! Unable License in 5508 controller
I am trying to install additional AP license in controller but "Command" option is not showing under Management -> Sofware Activation section to install license also I tried via CLI and getting error " License Installation is blocked by secondary co...
Hi all, As in title, i've setted up a guest wlan, pointing to a guest interface that connected to a XDSL router with DHCP. My private wlan works fine, clients have an IP from my Win DHCP server. That i want to do is to enable only wan access for gues...
I have some AP Meraki, which get failed alarms in connection with gateway. I've done the hard reset (some work) Procedure: delete from Network delete from inventory unclaim claimThe AP apparently goes offline for 4 minutes.But it doesn't work, I have...
I need to upgrade some controllers form 7.6.130.0 to support new AP models. The original plan was to go to 8.3 but due a bug CSCvf76274 we put this on hold. The fixed version for 8.3 is still not available so I am asessing 8.5.120.0. Unlike older ver...
Hi we know how to configure port security on Cisco switch to limit some user on the switch port. In WLC/AP side, do we have command whose function is like: switchport port-security mac-address xxx.xxx.xxx" Thank you
