Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
We have been dealing with a issue for a few months and Cisco are finding it hard to pinpoint the issue. We are runing a physical WLAN controller: AIR-CT5508-K9 and our APs are: AIR-CAP1602I-E-K9 & AIR-AP1852I-E-K9 The issue: We are experiencing rando...
how to set the Cisco signal so that it is more far-reaching (using cisco aeronet 1600 series)
Hi everybody Recently my team bought 7 AP's, we've configured properly. Example (it's not real escenario with fake ip address) management (vlan 10) AP1 (which is WLC too): 192.168.10.101 (WLC 192.168.10.100)AP2: 192.168.10.102... etc From WLC I can p...
Resolved! 2504 Wireless Controller - Login Issue
Morning, Not sure if anyone else seen this issue after a reboot of access points and the wireless controller where the GUI and the CLI page keeps asking for a username and password to login, I do know my credentials are correct. Sadly I'm not famili...
Hello, i bought 6 new "AIR-AP3802I-E-K9" APs and trying to setup a mobility express solution.My first Access Point is already up and running as a primary controller.Its not possible for me to join a second AP to this mobility express solution. All ac...
Getting error "Login Failure: Incorrect login credentials. You have entered an incorrect username or password. Please try again".I have created root access account on MSE already and got passcode from Cisco, but it still doesn't work.I am wondering i...
We have 2802's running 8.3.x code and a fleet of wireless comm badges that operate in 5ghz only. The vendor says to disable FRA which I did but I still see these things connecting to AP's that have the slot 0 radio in 5ghz mode. I would like for the ...
Hello i have multiple 2802i AP running Mobility Express image. Primary 2802I is working and controller is running off that perfectly but the second 2802i AP which was converted over to ME has also joined the Controller but no under ME AP i see no cl...
I has testing laptop connect wireless 802.11ac and transfer file is at speed very low 10-20M.How can i check that issue?
Seems like I need the latest IOS version (Autonomous - 15.2.4-JA1) in order for the AP to even recognise the module...Of course, it's not written anywhere on Cisco site, and I don't have access to download the IOS, so I'm stuck Can someone help?
Resolved! AP1262N with WLC2106
Is the AIR-AP1262N-N-K9 compatible with the AIR-WLC2106-K9? I have found a mention in the AP1262 documentation that a controller like 2100 4400 and 5500 can be used. But looking into the WLC2100 documentation I cant find the any referance for the ...
Resolved! MR authentication with MAC
Hi I have this client that requires heavy authentication on wireless devices since they have issues of employees giving out password of SSID to unauthorized clients.Im never new to MX but only more than a year to MR. Upon deploying MR33, I encountere...
Resolved! Honeywell 99ex models and MR52 AP
I am converting from a Cisco based WLC to a Meraki infrastructure. I am running into an issue with my Honeywell 99ex handheld scanners not being able to connect. The SSID is using wpa2-enterprise, AES, PEAP-MSchapv2. The SSIDs are about as exact as t...
I am unable to login to the embedded ap on an 891FW router. The router is running 15.4(3)M1 I have a console cable connected to laptop, using putty. When I issue the command "service-module wlan-ap0 session" I enter the username, then the password wh...
hi,i have one WiSM2 with 7.2.110.0 codes..all the data Network is perfect, but am getting some issues from Voice Network, whcih is basically in several location some phones are not able to make any calls with an error message "Network Busy".does anyo...
