Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! Update software vWLC
Good day!I received new access points, and they require firmware 8.5.131 and higher, my controller has firmware 8.1.120. I downloaded 8.2.170, as well as 8.5.140, I try to install it, but after downloading to the vWLC controller it goes into reboot. ...
Hopefully a quick question: On the proximity report in Location Analytics, are the "Connected" numbers unique devices, or does it count every time any device connects, even if the same device starts a new connection multiple times?
Is there a way of copying the config file from one autonomous access point to another? If so, will it replace the config during the copy? I have two cisco 3702 access points. I am looking for a way of getting the config from one to the other
Hello,I have an environment with existing ISE 1.2. I am about to introduce new wireless 1560 outdoor APs with 3504 WLC. I cannot see WLC 3504 (min SW version for 3504 is 8.5) on the supported devices on ISE 1.2. Will this configuration be supported/w...
Hi everyone We've been aiming to upgrade our WLC5520s across the globe to 8.5.140.0 from 8.2.x... However, today we found that Cisco recommends to perform an upgrade of CIMC to version 3.0.4(d) before upgrading AireOS. Here's the challenge. In my und...
Hello,I have a deployment of Cisco 2802I access points, WLC is 5520 running software image 8.5.140.0, and I have a problem where some users suddenly got disconnected and got the yellow exclamation mark on the connection status This issue affects some...
e are using 2802I APs and I need to know the recommended maximum number of clients per AP or per Radio, not the supported 200 max clients per AP. I have seen lots of recommendations saying that 20-25 clients is ideal, I am not sure how accurate this ...
I want to rename a site map in Cisco Prime Infrastructure (version 3.4). How and where do I do that?
Hello All, I'm trying to rename a site map in CPI. I've navigated to Maps / Wireless Maps / Site Maps ( New! ) > chose the site that I want to rename, but I'm not able to find any options to do that. Please advise where this should be done. Thanks in...
Hi Team,What is active and clear state means in CIsco prime coverage hole report. ALso , when i pull reprot from Cisco prime for coverage hole its showing two threshold RSSI value -80 & -95. But in WLC threshold is configure -80 only. WHy we are gett...
we have installed WAP150 Wireless-AC/N in cluster and configured two SSID's fro 2.4 and 5 Ghz. After some time AP dosent give ip to clients but connects to AP's. If we restart the AP's then it start Wireless working for 2-3 days.We are able to acces...
Hi All, We have configured an acces points Aironet 1850i with image mobility express.In my network i have 4 vlans.The access point is connected to the switch with a trunk connection for all vlans.We have configured radius authentication for all SSIDs...
Hi everybody, we're trying to implement a solution where a wireless client access to a Foreign WLC broadcasting a single Open SSID anchored to a DMZ Anchor Controller and there, based on AP Location or Group, got a different VLAN id. Is mandatory for...
I'm attempting to upgrade a Cisco Aironet AIR-AP1832I-B-K9 from 8.3.143.0 to 8.5.140.0 via http using AIR-AP1830-K9-ME-8-5-140-0.zip. The firmware uploaded successfully, but the APs were unable to download the software and errored out. I've attached ...
Dear Team, Kindly help to understand the practical power drawn on CISCO AP : AIR-AP1832I-D-K9 when connected to a Huawei POE switch : S2700-9TP-PWR-EI.As per datasheet it takes 15.4 however APs are getting mid power at WLC end. Are these compatible t...
Resolved! Cisco AIR-CAP3702e AP as Standalone
Hi,I have AIR-CAP3702E-D-K9 AP. I wanted to use it as standalone AP as I do not have any WLC as of now. Is it possible? Later, once I have the controller I want to use it through controller.Please guide.ThanksVishal
