Good Day All, Its me again................ I have a brand new Cisco 8500 WLC and on boot up it gets an IP and when I try to logon tot the console via web it wont take Cisco username and Cisco1234 password, please assist. See attached.........
Forum Posts
Resolved! New Network & Public IP
Hi. Some of our staff are moving to a WeWork-style office and have requested to use their own AP to connect to the internet. I have a spare MR 32 that I want to assign to this new network. I have created the new network and added the AP to it, but I'...
Logging into WLC admin web interface using chrome results in endless login prompts, untill the max requests exceeded error occurs or cancelling (resulting in a 404) and retrying in a new tab.Is the mobility express / WLC admin interface now properly ...
Dear All,our 8540 wlc (Rel. 8.5.140.0) doesn't seem to support radsec. At least we haven't found any possibility to configure it. We only find a button to activate IPsec or to define a port (obviously UDP).Is it true that as of now the Cisco 8540 WLC...
Hello Folks, I have a SSID with 802.1x PEAP as authentication metod, i want to know if there is some way or configuration on ISE to ask for the certificate on the client side. I want to configure that if you do not have the option to verify the certi...
Greetings , Can someone please share their knowledge and experience regarding solution/deployment of sms gateway for wireless controller for guest users of WLC to receive SMS notifications with login credentials etc? Is there any sms gateway soluti...
Guys, very basic question - how a client device shows single ssid when there are many aps installed? Example we have corp ssid and 10 aps in the floor. But our laptop/mobile shows only one SSID to connect (which means only one BSSID). on what basis? ...
Message: '802.11a/n' interface of AP 'abc' associated to controller 'xyz (192.168.1.10)' is down. Reason: Radio channel set.Failure Source: abc, Interface 802.11a/n WLC-- Model: AIR-CT5520-K9 Software version : 8.2.141.0 Prime-- Build - 3.1.0.0.1...
Good morning,if I'm right, i need to setup an ACL on Flexconnect groups to enable client isolation on a open wifi guest. Can you please guide me step by step ? Thank you.
When the WLC switches over only the Root Access Points (RAP) are staying in the network. The Mesh Access Points (MAP) dropoff the network and then join back. Is this an actual behavior? or the RAPs and MAPs should seamlessly join to the new Primary W...
hi,i would to control a capwap 702i with controller 5508, they are located in tow different network.the ap has join the controller but when i enable the wlan, no wlan appears.i'm using flex-connect technologythank your for event helps.
Resolved! 1111 WLAN Controller
Is it possible to turn off the status lights on wireless access points that are connected to the 1111 WLAN controller? I was looking for the option, but I do not see it listed. Thanks, Alex
My company recently upgraded their telecommuter networking hardware. They replaced the Aruba router with the Meraki Z3. While I like the speed and plug-n-play aspect of the Z3, I'm having trouble getting it to co-exist with my personal home network. ...
Resolved! Revoke successful WiFi AD access
Hi,I have enabled the Sign-on with Active Directory on our MX device for an SSID.How do you revoke this access for a device/user?Ive tried forgetting the device in the dashboard and setting the splash page renewal to 30 mins, but once the device has ...
I have problems: Access Point can't join to Wireless Controller[*07/07/2019 08:25:21.0000] CAPWAP State: DTLS Setup[*07/07/2019 08:25:21.0000] DTLS connection created sucessfully local_ip: 192.168.1.138 local_port: 5248 peer_ip: 192.168.1.10 peer_por...
