Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hello, I have around 70 access points which are deployed under a 3504 controller on the same network. My question here is regarding the flex connect mode, is there any mode where i use which will give the ability to the AP to route all data traffic...
Hi Team, My client has HP based LAN networking. And he wants to have Cisco Wireless solution for their office premises, which has remote locations as well. Do cisco access points and WLC supports for HP based LAN networking ?
Hi,My company has many locations which we have put a Meraki SD-WAN device at to VPN to our HQ. At HQ we have a Cisco ISE which we use to authenticate WLAN with dot1x. It works with most of our Meraki locations with no issues. But there are a couple o...
Hello. We have WLC 2504 set up at central site.When we deploy say AP1142, we just set local dhcp option 43 pointing to WLC, and ap registers right out of the box.But when we bought pack of 1832, we got a real pain in the (*).This device completely ig...
Our existing 5508 wlcs have "othIpsecCaCert" for IPSec and "bsnSslEapCaCert" for EAP Certificates. Our HA Pair of 5520 show nothing in the "security, advanced, Vendor Certs" area. Just blank. How do I get these created?Running 8.5.140.0
Hello all,Hope you all are doing well. Can anyone tell me what is the default password of wireless control system database? Note: we are using wcs 4.2.62.0 Any help is appreciated!
Problem Statement: iPhone silent disconnect issue in guest wireless network. Infrastructure setup: Guest wireless network has been configured with foreign and anchor controller with Cisco WAP/WLC and Cisco ISE with CWA. Open authentication. MAC Fil...
Good day!I received new access points, and they require firmware 8.5.131 and higher, my controller has firmware 8.1.120. I downloaded 8.2.170, as well as 8.5.140, I try to install it, but after downloading to the vWLC controller it goes into reboot. ...
Hopefully a quick question: On the proximity report in Location Analytics, are the "Connected" numbers unique devices, or does it count every time any device connects, even if the same device starts a new connection multiple times?
Is there a way of copying the config file from one autonomous access point to another? If so, will it replace the config during the copy? I have two cisco 3702 access points. I am looking for a way of getting the config from one to the other
Hello,I have an environment with existing ISE 1.2. I am about to introduce new wireless 1560 outdoor APs with 3504 WLC. I cannot see WLC 3504 (min SW version for 3504 is 8.5) on the supported devices on ISE 1.2. Will this configuration be supported/w...
Hi everyone We've been aiming to upgrade our WLC5520s across the globe to 8.5.140.0 from 8.2.x... However, today we found that Cisco recommends to perform an upgrade of CIMC to version 3.0.4(d) before upgrading AireOS. Here's the challenge. In my und...
Hello,I have a deployment of Cisco 2802I access points, WLC is 5520 running software image 8.5.140.0, and I have a problem where some users suddenly got disconnected and got the yellow exclamation mark on the connection status This issue affects some...
e are using 2802I APs and I need to know the recommended maximum number of clients per AP or per Radio, not the supported 200 max clients per AP. I have seen lots of recommendations saying that 20-25 clients is ideal, I am not sure how accurate this ...
Hello All, I'm trying to rename a site map in CPI. I've navigated to Maps / Wireless Maps / Site Maps ( New! ) > chose the site that I want to rename, but I'm not able to find any options to do that. Please advise where this should be done. Thanks in...
