Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi Please see the below, which is from output of command netsh wlan show interface in PC:My question is what decide the speed. In this case, Receive/Transmit Rate are 65 Mbps. It looks like distance and signal strength do not impact the rate. Anyone ...
Hi, good day, How do you configure TACACS on an HA pair? Do you add both redundancy IP's to TACACS? What about the VIP (management IP), do you need to add this to ISE as well? In other words, from ISE perspective to have SSH access to CLI, do you add...
Hello Together, i have got an AIR-AP2802e on my table, which has the following issue. When the AP is powered on it, immediatly stops even before u-boot, asking for board-selections from 1-5 (1= 3k, 2=2k new, 3=2k proto, 4= Milos, 5=3KH) you have no ...
Hello Team, Tried accessing the cisco ASA in GUI , getting the web page to provide the credentials but the page keeps on loading and not logging in. the acs is not a hardware and it a VM. Please let me kow what needs to be checked. +++++++++++++++++...
Hi, I am looking to replicate an existing point to point wireless connection we have spanning over the length of a cricket pitch. The current hardware is a pair of Cisco Aironet 1300 (AIR-BR1310G-E-K9) set in a root/non-root bridge mode which allow v...
Hi all,eWe have 27 MR33 AP's deployed at one of our manufacturing sites. We drop all the company traffic onto the local network. We have a guest SSID which is currently on our current Cisco kit. We are looking at moving this onto the new meraki kit.W...
I got jobs for replace AP1602E to 1815i, I would config same as last i did't found ACL setting in GUI or must config on CLI?. I'm never use WLC before(Controller configuration CLI mode). I try to swap CAPWAP (Look like SW,Router) mode becuase i only ...
Hi group, I hace a 1602i autonomous running latest IOS. Powered with power supply, connected directly to cisco switch on a Gig int. I can't have more than 100Mbps connection speed, if I force, port shutdown. Tried, different switch port, different ca...
Is there a way to print a list of all the devices in our organization and if the device is associated or not? I'm sure I could write something to get all the networks, then query for the devices per each network. It would just be great if there was a...
I am seeing continuous disassociation/association and deauthentication/authentication happening on one of my MR32 APs. Can anyone offer advice?The example below is a RaspberryPi device, but I also see it on a Windows 10 laptop
We are happy to announce the new portal for Wireless Troubleshooting tools: https://developer.cisco.com/docs/wireless-troubleshooting-tools/ (Externally accessible) We are excited to become part of the Devnet community, and provide a wide range o...
Hi,Is it possible for email notifications to be sent to approvers when a new guest wifi account is created by the guest user? This relates to a Sign-on with Meraki authentication set on the SSID.The example I can provide is:Guest enters their details...
Recently we ran a Nmap scan of our wireless network using a client connected via Wifi. The scan showed common ports over the dynamic interfaces (80,443, 22,) as open and reachable from the client. Further testing showed that we were able to connect...
I've just deployed a new solution and im experiencing issues with clients not roaming properly. Access points are installed really close to eachother. There is 6 access points loated around the premises. For example im in one room, i can see that i...
Will it damage 3502E or 3602E, with the radios turned up to max power, to operate without 1 or more antennas? I tried hunting this up in the FAQ, etc but didn't find anything specific to these models.
