Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi there, We have a complete Cisco Wireless setup. We need to implement BLE Beacons. what pre-requisites are required to implement BLE beacons. Thanks in advance.
Hi, I was wondering if you have experienced adding a third-party WiFi Access Point to your Meraki network to extend WIFI coverage. If so, tell me your experience.Current Setup: MX64+MR33+Archer C7So far, MX64 manages the network as it act as a securi...
Hi All,I have a question I will implement WIFI at different country just install APs (Flex) other country but center WLC(5520) install at my country afterthat i need APs will go to internet and join to my WLC center. anyone can have experience to di...
HiI am looking to advertise a number of wireless profiles for an organisation that has a presence on our campus. I will use our APs to do this and then run Foreign/Anchor set up for each profile so that clients of these profiles break out onto the o...
Hello, On 802.11a/n/ac 5Ghz WLC 5520 configuration, for on of our Cisco 3702E APs, the power is currently configured to 1 (17 dbm ~50 mW) when we are below this AP with a scanner Datalogic FalconX3+, in the status of the scanner it shows 80 mW for tx...
Hello!I have a problem with ap AIR-AP1815I-R-K9i have 2 AP and they have same firmwarecisco AIR-AP1815I-R-K9 ARMv7 Processor rev 5 (v7l) with 1015824/668048K bytes of memory.Processor board ID FGL2237B10GAP Running Image : 8.8.120.0Primary Boot Image...
Good Day, I have received several reports over time from the same physical location regard their inability to authenticate to an 802.1X WLAN (Radius server online and reachable with no errors on the server.) Generally, it will only be a handful of AP...
I have ran these debug commands and below is the output the I recieved.debug mac addr AP MAC ADDRESSdebug capwap event enabledebug capwap errors enabledebug capwap detail enabledebug PM PKI enabledebug DTLS Event Enable *spamApTask1: Apr 24 13:35:35...
hello Masters of Wifi, I need to undersand how AP/wireless network desgined, how many mode do we have when we set up wireless, I know we have AP local mode, flexconnect mode, but I don't know how they defined, like how it works, traffic from AP will ...
Dear all: mi wlc 5508 log show me this message : - IDS Signature attack detected. Signature Type: Standard, Name: NULL probe resp 1, Description: NULL Probe Response - Zero length SSID element, Track: per-Mac, Detecting AP Name: -Client Deauthenticat...
Hi experts, Is there any way to create access list in wlc line vty? Via CLI or web GUI is fine for me.So i want that wlc can be ssh just from certain ip address.
i'm trying to assign a static IP address to a specific client mac address on the 1602, i cant find a way to do this from the GUI , the AP is stand alone , i have it connected to UCME test network for wifi handsets , so i need these devices to be give...
Last time my network only 1 segment with IP 192.168.0.0/24. and my Meraki AP works fine.I have 2 SSID : bridge mode & NAT (DHCP Meraki)Then we implement VLAN in our network, now Meraki AP port in switch already change to VLAN Client segment with diff...
So weird thing happened Tuesday which I brushed off and was like Eh. Users were reporting getting kicked off wifi and re-associating. So I went to check it out and stood there till I saw it happen. I looked at the AP and in channel it said Radar dete...
Hey, I am currently doing some research conerning the implementation of WPA 3, but it seems to be impossible to find anything official from Cisco about this. Will the Aironet 3802 support WPA3? Which WLCs will support WPA3?Is there any date, when sof...
