I have a Cisco 3502I Access Point that shows as registered in Prime Infrastructure but it is not accepting clients. I have already deleted it, added it back, and it has been rediscovered by the WLC but it still does not accept clients..... Can s...
Forum Posts
Hey all, After upgrading my WLC 2504 to 8.4.100 i no longer had the 25 licenses that the device shipped with from the factory.. Any idea what happened or what i can do to get them back. Been running on the temp licenses for a few months until i ...
Hi, Currently, I have 10 APs and would like to add extra 5, problem is I get no reply from tftp server error.I've already enabled the port on inbound and outbound on the firewall, still no luck. Any help would be appreciated.
Hi,I m new to wireless technology and currently we have 2 Critical and 2887 Minor alarms are showing in Cisco Prime.Most of these alarms are relate with the Rogues configuration under Cisco Wireless Controller.Because unclassified 2586 Rogue Aps and ...
Hi guy’s,I have a problem with one of my access points (AIR-AP1832I-E-K9C).When the access points is booting, the access point going in error.On the console view get I a message from L2 error detection.Means this that there is a problem with de NIC o...
Hi Folks,we have been suffering a bit with a subset of Samsung phones which simply shows the against the Wi-Fi No Internet connection. These seem to be recent phones a Note 9 and an A8 (or A9 the remote engineer was vague) running Android 8.1.0 from ...
Resolved! Total number of clients counter
Hi, is there any way to count the total number of clients that have ever connected to an SSID?I'd like a webpage with a counter - total number of new clients connected = nSo that every time a new client connects to a specific SSID the counter increme...
Hi, I am planning to upgrade 5508 WLC from 8.0.122.39 to 8.5.135.0. As per release notes of 8.5.135.0, anything prior to 8.2.15x has to be first upgraded to 8.2.16x or 8.3.x and then 8.5.135.0. The WLC is currently running 8.0.122.39 and it's a backu...
Hello experts, I am setting up a new vWLAN Controller version 8.0.152.0 with AP1131AG access points.The controller address is 172.16.10.5 the 2811 router is configured asip dhcp pool APnetwork 172.16.10.0 255.255.255.0default-gateway 172.16.10.1op...
Hi , any pointers appreciated. GE patient monitors (Carescape B450) - use broadcast/unicasr from Monitor to Host and back (GE monitor has static IP and has server IP defined) (units do not support multi c) GE monitor – network attach...
Im trying to setup mixmode on a single floor on a CMX 10.6. But I just cant seem to grasp the syntax of that command. No matter what I type, it just gives me an error. The closest I got to having it work was : "cmxctl config hyperlocation mixmode 762...
Problem i have network managmnet 10.1.1.0 for acces point and network 17.20.128.0 /24 for client wirless Problem client wirless and accces point get the same network !! So how i can allow client wirless get 172.20.128.0/24 and not 10.1.1.0/24 in...
Hello all, I'm trying to configure Radius authentication for Administrators on a WLC 5508. I have the radius working on all of my Cisco Switches, but it appears that the server is not configured correctly for the WLC. Does anyone have the proper...
I have a few questions to see if anyone has suggestions or more info. I've always been told to not mount an AP to an I-Beam as it messes with the signal. Now, we have a new warehouse being built and the entire ceiling structure is I-Beams. So, How...
1) Does a NME-AIR-WLC6-K9 work with a Cisco 2911/k9 router 2) Would a used one include the SRE?3) If not, can the SRE be purchased separately -what is the part number?4) I want to add 1-2 access points (AIR-CAP3702i) to my home network - would I be ...
