Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi, I cannot find the difference between AIR-PWR-C and AIR-PWR-B. Maybe someone can help. Can I power an "old" AIR-CAP1602I-E-K9 with AIR-PWR-C? Is AIR-PWR-C per default delivered with AIR-AP1832I-E-K9? (In the data sheet and getting started guide I...
Hi, 1. Just trying to understand the dynamic TPC on the Cisco 5500 controller on the 5 GHz band and 20 MHz wide channels (keeping the example simple). The default settings enable TPC adjustments between the Max (30 dbm) and Min (-10 dbm) power level...
We have two (2) WLC 5508 currently in production, each with associated Access Points and Wireless devices. Now we would like to configure the redundancy between the two wireless controllers. I have not done configuring two devices in production with ...
Is there a good document available that details the latest (April 2017) thinking and best practice for the use/config of a single WLAN/SSID supporting PCs running softphone and or interactive voice/video (Skype, Jabber, etc.) in a controller based wi...
Hello, i have installed a 5520 as the local controller und a 2504 as the anchor controller. Both coltroller have the code 8.2.151. Every thing goes up and it look fine, but the clients have a slow connection. Here are my questions: 1. Is the combi...
Hi I have taken a new broad band connection, which I am not able to use it through my WAN4410N wireless access point as the service provider says this router does not support PPPoE. Can anyone please help how to enable PPPoE or any alternate ways to...
Have 24 of the Cisco model 2702I access points and a pair of 5508 controllers. ISE is being implemented. How does it handle it when a client moves from one AP to the next? Is there anything we need to be aware of?
Buen día, Ap 28xx WLC 25xx El ap se registra bien en la Controladora pero el Ap no registra clientes, ningun cliente logra engancharse Por favor una idea del porque puede pasar, actualmente estan actualizados Muchas gracias
With the departure of the 1600 series AP's, I'm looking at other AP's to buy in their place. The 2700 series seems the next best step. One thing that confuses me is Controller vs. Autonomous. Can all 2700 series AP's be set to boot and use Autonomous...
Resolved! ISE Primary/Secondary max latency
Hi There,My understanding is that you can run ISE with one node set as primary and zero or more nodes set as secondary, with the secondaries located closer to the end points.1. Does this mean the local users closest to a secondary node will authentic...
Hi everyone, I came across an issue with the 8.0.140.0 firmware on our WLC and thought I'd ask to see if anyone else has experienced it or if it's a known issue. As background info, we had release 8.0.121.0 running on a 5508 WLC with a mix of 3500, 3...
Hi Team, I have a situation here, we have a site power down with around 25 flexconnect AP's, now when these AP's will go down it will generate a TRAP on controller and an Alarm on Prime, I'm fine with a TRAP on the controller but can we stop the Ala...
Hello, i have been looking a PI API that can filter AP BSSID based upon Friendly_Rogue_AP type parameter. Can this be achieved using PI 3.1 ? Thanks !
Hello, I would like to get some opinions on grouping multiple dynamic interfaces (VLans) to a SSID vs using one large subnet. What are the advantages or disadvantages or is it only preference. I hope I'm wording this correctly.
I have a 5508 controller where the GUI says that there are 400 AP licenses loaded on the Monitor page. When I go to Management>Licenses, it shows that I have a 500 AP count license that is active. CLI confirms this AP count. How do I get those oth...
