Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Good morning, please, may you indicate which maximum value (in dbm) LTE EHWIC can transmit ? I found this value for wireless boards but not for LTE (for example, an 802.11b/g/n card can support, respectively, 19,16 and 15 dbM as maximum tx power.....
Hi, We have installed Cisco 5508 with HA setup with 50 license. However used is only 25 access points. We are looking for another site with 10 access points. Is it possible to deploy the HA to the other site and make use of 50 license at both the. o...
Hi, I have APs in localmode. Is it possible to create a new SSID that should drop the data localy without converting to FlexConnect? The switchport that the AP is connected to have to be configured as trunk, it is now access-port. MVH Philip
Resolved! Same SSID name in different locations
Hi I 2 lokations. A HQ and a WAN location. I am interrested in having the same SSID in both location, but the HQ SSID should use local mode, and tunnel to the WLC. And the WAN should have FlexConnect with local breakout. I have configured 2 differe...
Hi Everybody I have a WLC v7.4.100.0 and a AIR-CAP2602I-E-K9 and they are working perfectly. I got a new AIR-CAP2702I-E-K9 it gets an IP address but it does not talk to the WLC. Can somebody help please. Thank you. Cisco IOS Software, C2700 Software...
Since in theory it is a good thing should I always enable infrastructure MFP? Are there any drawbacks?
Hi I'm publicly broadcast fews of operator ssids in public area. This public area already has those ssids braodcasting. I'm a area's landlord. I invested for 802.11ac wifi. But operator wifi infra around me running poor is 802.11g/n I need to config ...
Hi All , i have cisco WLC 5580 , it was working fine , but now i am unable to access it through both GUI or CLI , if i reboot the WLC , it will fix the issue for few minuets ( GUI & CLI works ) , but after that i am facing the same issue again . pl...
Hi All Please kindly answer to me , how to install c1140-k9w7-tar.124-25d.ja2 (Cisco Virtual Access Point) in (GNS3 or oracle VM box or Vmware Workstation).. Because i am try to Wireless Lab , Thanks you so much
Hi there, On ISE 2.0 I have wireless authentication policy which assigns devices in Blacklist identity group this authorization profile: Access Type = ACCESS_ACCEPTcisco-av-pair = url-redirect-acl=BLACKHOLEcisco-av-pair = url-redirect=https://ip:port...
Hi, everybody I just configured the alarms sending on Cisco Prime Infrastructure 3.1.0.0.132 and worked fine, but I got a problem. We have many frequent mails from unreachable alarms and it fills our INBOX, so we need to configure something in som...
Hi, we are planning to buy some Cisco AP 2800 to expand our Wireless Network. We currently own 3 Cisco AP 1250. Can AP 2800 and AP 1250 connect to the same vWLC?Can AP 1250 running 15.3(3)JA10 IOS connect to vWLC running 8.2 or 8.3 software?
Hello, we have an issue with a cisco WLC controller 2504 with 25 AP's connected. This controller is in replacement of another WLC 2504 which was damaged one week ago, but because we didn't make a backup from the previous controller, we had to configu...
Hello, I have an SSID with dual band, the 5GHz band is ok, but I want to know if is there any way that in the 2.4 Ghz band can I specify that 802.11n radio would be preferred over 802.11g, because I see that many people are automatically connected to...
I have a 4402 in production, I have a device called eWon that connects to the 4402 wireless with 2 ip's. The Ip's are routed interfaces on the eWon. How can i get the 4402 to recognize the 2 Ip's? I already disabled IP-MAC Address Binding, but am n...
