We are using two IOS AP(AP1130)s and 20 LWAPP AP(1130)s with WLC4400. 20 LWAPP APs are converted IOS to LWAPP two weeks ago successfuly. but today i've tried conversion 2 IOS APs to LWAPP AP with Upgrade tool. The image conversion is OK and get IP Ad...
Forum Posts
Hi Sir,On a WLC4404, the default data rates on the 802.11b/g Global Parameters are as follows:1 Mbps - Mandatory2 Mbps - Mandatory5.5 Mbps - Mandatory6 Mbps - Supported9 Mbps - Supported11 Mbps - Mandatory12 Mbps - Supported18 Mbps - Supported24 Mbps...
Folks, Once in a while i have noticed that the APs loose their config and register with the controller with theia mac address instead of their name and loose the AP group and flex connect information. Ay ideas why it is happening to some...
Resolved! Walled garden Utilisation
I have a Walled Garden set-up with more than one destination address configured. VPN clients use the facility so that users can associate with the AP with no authentication, but can only go to (internet exposed) VPN concentrators without the extra st...
Please tell me basic steps for configure it. I want to make this switch DHCP server for WLC setup .
Resolved! Wi-Fi RADIUS Authentication failed
Hi experts,I am using RADIUS authentication to connect to the Wi-Fi network, I have two Windows Servers with AD where I have aggregated the RADIUS role and created the RADIUS clients, and so on. With the primary RADIUS server it works fine, but with ...
my problem is that I have an ISE joined to an AD and have a Cisco WLC as a network device I have authentication rule and authorization profiles that give back a VLAN, that redirect to an interface on the WLC The problem is when an Android smartphone ...
Hi Community. We have a strange behavior. We setup 802.1x with Windows NPS. The Windows 10 can connect without an issue. But the Windows 7 clients can't connect some how. I did a "debug client" on Win7 and Win10 (attached to this post), but i don't s...
Hi there, is it possible to run N+1 between a primary 3504 and a secondary 5508? When running N+1 do all AP groups need to be configured with the same names? Do the AP groups also require the same members with the same wlan ID's and settings? Do f...
Hi All.I've an issue with a 1522 AP connected via Ethernet to a switch.This AP will not associate to the controller.A LAP1242AG will associate without any issues.I assume maybe its a controller software issue?The controller runs 4.0.217.0Appreciate a...
Hello All, Opened a TAC case for the above issue. This is specific for customers who are using mobility anchoring solutions with their customers or partners. Cisco created a bug ID for this issue and are currently investigating. Kindly note this is n...
Hi All, I would like to share my experience after upgrading my WLC's in a HA pair from 81.131.0 to 8.2.121.0. It has been a week since I have upgraded the 8540 controllers in HA pair to 8.2.121.0 code which is termed as a "stable code". I have alre...
Resolved! Joining AP to vWLC
Hello, I'm running vwlc 8.2.166 on esxi 6.5 on VMWare Workstation 12. All the initial configuration is done, and I can login to the WLC web GUI. This is my first time using WLC and AP, can someone help me connecting AP to the vWLC? What else do I nee...
Hello ,I am not sure if this is the right forum to ask the question but we are having a problem related to MSE product .We are currently running software based MSE which at its base runs over RHEL 5 . But our corporate policy requires no RHEL based s...
Hey guys, I have a simple question can I change the name of the SSID once its been implemented?basically if SSID = WORK, can I change it to Office WORK?I want to see if I can avoid deleting the SSID completely and starting over. Thanks for your help.
