Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello everybody, WISM 1 Slot 2 is not reachable via its management ip address. Only via service ip reachable. (WiSM-slot28-2) >show logging*nim_t: Jul 06 07:47:23.087: %SIM-3-PORT_UP: sim.c:9982 Physical port 4is up!.*nim_t: Jul 06 07:47:23.084: %SI...
Hello I have 8 router cisco wap321 and I need to set a unique wireless network in a big area. (all of them with the same SSID) So the users can have a transparent network roaming between the routers so I would like to know which is the better way to...
Hi In our project we configure two wism controller and it is installed in 6500 series switch In Each wism controller they are two controller Altogather they are four controller each wism module will support 150 APS in our project they are 210 APS of ...
Resolved! AP 1702i bug - I need a workaround...
Hi community, I found out after one week of testing: My AP 1702i (autonomous, latest SW) doesn't allow my wireless devices (iphone, notebook) to reach some SSL/TLS sites like https://businesswebmail.a1.netorhttps://www.bawagpsk.com for example. Some...
Hello, I have installed CUC, CUCM and CUCM IM&P (9.1) and a 2504 WLC. Everything is working fine but some users experimented choppy audio on the jabber for win 10 using the wireless network with the wired LAN don't have any problem. There is no trigg...
Hi, I am looking at deploying 1500 series AP's to connect multiple remote buildings. Normally we would fit dual devices to ensure redundancy, however our existing switches are none managed so I cannot change any spanning tree configuration on them. P...
Hi, Any of you know why is not possibe to carry out a network discovery with wireless conection? If I connect by cable I can discovered all the machines on my network. Do I have to enable something in my WLC in order to do this? regards
Resolved! Access point Signal strength
Could someone please tell me how to configure my WLC 2504 to set the associated access points signal strength to maximum?
Resolved! 2702i AP client support
Hi. I am Hammad, A representative Engineer from a company " TechAccess" in Islamabad, Pakistan. We are selling one of our customer's cisco 2702i Access Points. As the clients requirement is to give internet connectivity to large number of hosts, a qu...
I am looking for a walk-through or some sort of guidance on configuring an access point in monitor mode to detect a rouge AP that I place wired to the network to detect that rogue AP and to alert me to the existence of that rogue AP. I have the 5520 ...
Hi, Does anybody know how to check on MSE or on PI regarding how many licenses used by wIPS module? Kit list and software version as under; Prime Infrastructure 2.2.0 (2.2.1) MSE on VM running version 8.0.130.0 WLC 5508 version 8.1.131.0 AP 3702i Li...
Hi, There’s a virtual IP address that’s unreachable in the new cisco wireless network. Its supposedly a Microsoft cluster IP address for CAS(customer exchange server)Server. The server has an IP address that’s reachable. I am looking for some rule to...
I would like to know if Cisco does have Autonomous AP's on its 1700 series? Are there any outdoor wireless that can link buildings within 500 meters distance with clear line of site?
Dear Cisco Team, Please tell us, how to enable "Link Measurement request/Response" for Cisco WLC2504 I am not able to see "Link Measurement request/Response" from Cisco WLC2504 Thank you Pramod Ganigi
Hi, we have switch Cisco switch WS-3850-48P-S with primary and secondary power unit(715WAC+715WAC).In this case we are require the particular port to assign max power 30 watts. Let you know above model switch to assign upto 30 watts is possible or no...
