Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Lately, we got a lot of " Reason: Radio channel set. Failure Source: AP , Interface 802.11b/g/n" from some APs. Do you have any idea? Thank youJessie
Hi all, I have just tried to upgrade a Cisco WLC 8.0 to 8.2.151 (latest recommended). This is hosted on a UCS C220 M4 with firmware 2.0(6d), what version do I need to upgrade this to prior to the WLC as the documentation is not that clear Regards and...
We have a customer using webauth etc but we're unable to get the FQDN ACL working properly. They are using a guest anchor (mobility). We have set the ACL on both controllers and added the URL's to the ACL. If we remove the anchor and use the foreig...
Dear All, this morning I had the bad idea of applying the firmwa update to fix the known bug WA / WPA2 KRACK. The release that I've installed is 8.5.105 , it's seem to be the last. After that all of my wifi client , Macosx Android and so on , have ...
I recently added a Cisco 1810 OEAP to my Cisco 2504 WLC and everything is working great except for the PoE port. I found in the configuration guide that the port is disabled by default and it includes a command to run but I could not run the command ...
Hi, would appreciate if anyone can explain following question. Network Component; Wireless controller : 8510 Client = Cisco phone 7925 AP Mode : FlexConnect (local switching) Authentication/encryption : WPA2/PSK (AES) Site AP count = 66 Flex conne...
Hello, Our client encountered the following problem: 3650 switch was configured as a mobility controller. Everything was ok. But today approx. all clients stuck int the APPLYINGPOLICY state. I couldn't find any solution for this issue.
Hello,I configured on my WLC 5508 a new Interface & VLAN . The WLC act as DHCP Proxy.I enabled also Flex Connect local switching . Then I removed on my Switch under the VLAN settings the IP helper because as I know the WLC act as IP helper. What is ...
I have an 1832i that I'd like to use on a WLC 5508. Is this possible? Do I need to change the IOS on the AP or is already provisioned to use either a WLC or the Mobility Express?
Hi All, Just hoping to get some feedback about the potential security risk involved with per-SSID VLAN tagging and Meraki APs. From what I've read here: https://documentation.meraki.com/MR/Client_Addressing_and_Bridging/VLAN_Tagging_on_MR_Access_Poin...
Hello I am using 10 number access points 1702i Autonomous AP IOS Software-15.3.3-JF1(ED), ISP broad band is 100 mbps when i was connected to ap it is show 15 to 20 mbps and when was connected LAN speed is 90 to 98 mbps cloud any one help us rega...
Here i my problem... When some clients are connected on 3 SSID'S, 10 or 15 mn after, they are deauthenticated.. and they have to connect again on the SSID.What is this ReasonCode2 ? there is always a reasonCode but i don't really know the meaning.. T...
Hi Just upgraded 8510 from 8.0.120 to 8.0.140. we have 3 in HA pair. Issue, upgraded 1 WLC to 8.0.140 now the control path is down eping work reponds icmp respnds mping fails. These where working before hand, the other 2 HA are still working is...
Hi, With a Radius server (like ISE) we can push the vlan ID to WLC for move device to a specific vlan with attribute "Tunnel-Private-Group-ID" if option "Allow AAA Override" is checked.In WLC we can create a group of vlan but anyone know if it's po...
Hi I am using CISCO WLC 2112 in our enterprise network and as we all know about the krack threat or vulnerability. so i just need help to protect my WLC and AP's from this threat. is there any need to upgrade hardware of WLC (Because WLC 2112 is ...
