Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi.I want to buy two wlc 5508 or two 5520.please help me if i want to use these WLCs in HA mode how to ordering(Part numbers) for Devices & Licenses.So i don't know that must buy APs License for one of wlc or for both.please help me with a sample ord...
Hi,Please help me with a sample ordering HA WLCs for 75 APs for 5520 package with all of part numbers to needed.thx
Hello colleagues, WLC 5508 / 2504 8.3.112 PI 3.2 SNMPv3 AuthPriv I haven't found any way to restrict the SNMPv3 communication with an ACL that points to NMS/32. However, it's possible for SNMPv2c via config snmp community ipaddr ip-address ip-mask na...
Just curious if anyone know or can point me in the right direction to the reasons why the controller would admin down it's management port. I added a second Controller to my enviroment and created a mobilty group for the two and for some reason the n...
I want to disable B and G, but not N (2.4) yet.On the controller, Wireless / 80211b/g/n / Network, I can disable/enable "80211b/g Network status", will that disable the whole 2.4 radio, N also ?If so, is there any other way of doing this, or should I...
We have just purchaed AP2800I When we plug it in we are getting: Discovery Request sent to 255.255.25[12/19/2016 01:13:16.3400] device capwap0 entered promiscuous mode5.255 with discovery type set to CAPWAP_DISCOVERY_TYPE_UNKNOWN(0[12/19/2016 01:1...
Hi All, I have a problem. Between the 1600/2600/3600 and 1700/2700/3700 generation of AP's, Cisco appears to have changed some of the regulatory domains-to-country-code mappings. My WLC is set to operate in -A and -N regulatory domains, and we have ...
Just lately my Virtual WLC keeps reboting its self. Sometimes it will last 40 mins sometimes a few hours then it will restart. Anybody else having this issue?
I have another AP (cisco air-ap1131ag-a-k9) that I would like to use and configure on the MS220.Can this be achieved?
As part of our PCI compliance, we need to alert and detect ROGUE AP's that have been purposely or inadvertently connected to our Corpotate network. I'd like to "tune out" ROGUE AP's which have zero clients connected to it? I know there is a conditio...
2 - ISE servers providing only Administration and Policy Service2 - ISE servers providing only Monitoring service The question i have is about the settings on the 5508 WLC for the Radius Accounting servers. Are the Accounting Servers the IP addresse...
I have 2 2504 WLC in production. only difference is the software version. 8.0.115.08.2.161.0 The newer software version seems to be missing some SNMP OID's.Root OID: bsnMobileStationRssiDataTable:: 1.3.6.1.4.1.14179.2.1.11.APIfPhyTxPowerLevel (1.3.6....
Hi Everyone, After I have setup the Switch, WLC, Server, under the wireless I could only use Ip address to access the servers but not with domain name. Under the Lan I could use both. Is there any setting which I need to setup with the WLC or someth...
I heard that Cisco terminated creation of standalone access points (1600 series probably the last one with stand-alone option).Would be good to have some confirmation on that.
Dear All, I have got an AIR-CAP2702I-E-K9. Is it possible to make it work in autonomous mode. As per the data sheet it will work both in controller based and stand alone. But how ?? Need to change the image ?? Now it has a combined image.Thanks in ad...
