Hello Team,we are facing issue owith the guest users as the users arte not getting the authentication page.Authentication method: Mac filetering Ap-mode: flex connectController version:8.5.182 The user request is being hitting the ise and the ise is ...
Forum Posts
Description: AP1552H not able to provide data over PoE port Detail: AP model 1552H is connected via DC for the power and connecting a camera on the PoE link (with IP static preconfigured), the camera turned on by the PoE out but there is no traffic c...
Hi, Is there a way to actually disable the DHCP server completely on the WAP581? I see in the manual that it will 'start a dhcp server' if it sees DHCP requests from clients go unanswered.. but I'd like to know if I can just shutdown this service com...
Hi, we have purchased 5 x Volo FM1200 units to use in a MESH network on an Airport. We have tried several frequencies & they keep dropping the link randomly. We believe there may be some interference issues. Does anyone have any suggestions to make t...
WLC Config Converter (AireOS, IOS-XE) External Link: https://cway.cisco.com/wlc-config-converter/ Goal of this tool is to provide easy config migration between various wireless platforms.One tool can perform following operations: AireOS(2500/3...
Hi, does anyone know how to disable LLDP on a 9115ax access point that is in CAPWAP mode and connected to a Cisco 9800 WLC I am running version 17.9.4a of code with the latest APSP I want to disable LLDP on the AP's as it is creating unknown protocol...
Like the title says, I have a C9130AXI-B that boots fine until it joins the controller. Once joined, the controller initiates a reboot to load the backup image to match the controller and the image seems to be corrupted as the WAP crashes. The WAP re...
Hello Cisco WLAN experts,this big hospitals deployed Cisco 9130 WLAN APs also in rooms for patient and call-on-duty rooms for doctors and nurses.To not disturb the night silence by green or mostly blue LED of WLAN APs, we disabled LED- and Flash-stat...
Dear All,We have a below scenario : Our expectation is the user will get ip address from DHCP server while connecting to SSID. All SVI for service ip is configured in Core Switch except WMI ip, that's why we have created just service VLAN in L2 on W...
Resolved! Cisco 5520 WLC WebAdmin Cert
I'm trying to install a WebAdmin cert for a Cisco WLC 5520 version 8.5.151.I generated the CSR via CLI and had it signed. I uploaded the .pem file to the controller. It's returning a certificate error of NET::ERR_CERT_COMMON_NAME_INVALID when visitin...
Hello,I just experienced issues with a C881G-4G-GA-K9 (no IP-Address on the interface, no service...). In the output of show cellular 0 all, in the Data Connection Information I got following:Data Connection Information===========================Pro...
HiWe have a setup of CW9166I Access Point connected to C9800-CL vWLC.We are able to check the temperature of the Access point using the below CLI command,AP149F.430E.DC80#show thermal-control-summaryCPU temperature = 56 CRemote sens...
We have a c9800-48 controller connect with 93 of c9115AXI, controller monitor by solar wind, AP goes down randomly and rejoin again without disconnecting the session. Alert is similar to below:The following Access Point went DOWN on 27 October 202...
I am unable to access my AP.I have checked my com port and put the same com port in putty but here is nothing showing except black command prompt.Also checked below point Baud rate: 9600Flow control: disabledCharacter side:8Stop bits: 1
We are trying to implement 802.1X authentication with EAP-TLS, I would like to know if using an internal CA, using a self-signed certificate, we can carry out this implementation, if it is not possible, do you know what type of certificate we should ...
