I have 10 Cisco Access Point 1852 working as ME , 9 are working fine but one working as stand alone ME due to diffrenet firmware versionhow to convert or upgrade to the other ME (9 AP)
Forum Posts
We are developing an application similar to a DATA LAKE, meaning it will process data and similar tasks. We need to extract some data from Wi-Fi, specifically from Cisco APs and controllers. Which API is used for that?" Is this for a project you're w...
Hi Everyone,Just would like to confirm if AIR-AP3802I-K-K9 supports the flashing LED function. This is due to there's no physical label on the AP, and we would need to identify the AP manually at the site for some reason.I found the documents below r...
Hi All,We have a Meraki WLAN Guest SSID going into a Bridge VLAN, on Meraki Switch, true a Meraki Firewall into the Internet. As it is a Guest VLAN we activated the Layer 2 Isolation. now we need to Whitelist 1. MAC Address witch should be Accessible...
I am planning to deploy Cisco IW9165D CURWB units. One end of the link is to be mounted on a pole. I am being asked for the Wind Loading number. If add a horn antenna the datasheet provides this figure. But I don't see it in the datasheet for the IW9...
Wireless firmware versions MR 31.1.5.1 changelogImportant noteWi-Fi 5 Wave 2 MRs support - This version and subsequent MR 31.x.x are only supported on 802.11ax (Wi-Fi 6) and newer MR models. 802.11ac Wave 2 and older products will not upgrade if they...
Resolved! Meraki firmware upgrade to MR 31.1.5.1
Dear All,I have MR36 and MR86 access points with firmware version MR 30.7.1. I have observed that clients utilizing WiFi 5 are experiencing reduced link speeds, an issue that appears to have arisen following the firmware upgrade to MR 30.7.1.Could yo...
Resolved! 9800-WLC How to disable Session Timeout
Hello Cisco WLAN experts,this huge hospital is using a patient WLAN and people are complainig about being cut off the WLAN for patients after estimated every 15 minutes.I found out, that on our good old 5520-WLCs, which are still hosting a big part o...
I would like to find an Aironet indoor AP that will operate in Mesh mode with wireless backhaul. Looking at the compatibility matrix for 8.5.182.x I need to stick with 1600, 1700, 1800i, 1810 OEAP, 1810W, 1815i, 1815m, 1815t, 1815w, 1830, 1850, 2600,...
Good day,Back when I was still using an AIR-CT-5508 (home lab setup), the unit had the ability to do a hardware connection to two separate networks. The way I had it set up was one of the SSIDs (the guest side) would (with the right password) route a...
Hello I am new in my current role and have recently started working with Cisco Access Points. As part of my testing, I am evaluating various operational modes (local, monitor, sniffer, flex connect) on a 9115AXI-K AP connected to a Cisco C9800 Wir...
Are there any plans to release an indoor ruggedized Wi-Fi 7 access point, in addition to the fully indoor range that has an external antenna connection option? What I am thinking about is something to replace a 2802E or 9120AXE for example, and it be...
Hello, as shown in the picture belowI'm thinking of installing Access Point on a wall that's 8m high..Like the point of use, we need to provide 50 meters of service with one access point 3 meters long from the floor, and I would like to ask which ant...
Folks ,Our WAPs are set up on the Management VLAN 50, while the wireless users obtain their IP addresses from VLAN 80. Authentication is managed through a RADIUS server. Is it essential to enable inter-VLAN communication between VLAN 50 and VLAN 80 f...
Hello Team, i am trying to deploy the two C9800-40-K9 controller in the network1- Before connecting the both controller to the networki had given one ip adress 10.91.225.80 ip to the Gi0 of WLC1 and connected the cable between SP port and laptop wit...
