Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi guys, Within two months, I got 3x WLC 2504 RMA approved and been replaced !! Is it just "murphy law" or I'm very bad lucky... or YES, its the reality and WLC 2504 are very sensistive? I'm very tired of this, and I'm starting to think to not sug...
I have a new primary 2504 that is running 8.1.102.0, and an HA 2504 running 7.6.101.1. Question is, can I download the IOS from the primary 2504 to the HA controller? Does it matter if it's an HA controller? Thanks
Hi, I am not sure if I have placed this question in the correct entity. But we are experiencing a weird behavior in our wireless network. We have a WLC in HA AP-SSO setup with 1602i and 2602i Access Points. We have 2 SSIDs, 1 for guest and the othe...
Hi What is main feature of WLC 4404 that 4402 does not have ? or send me a link. I want to buy WLC for ccnp/ccna lab. Thank you
We discovered that the WLC was generating a lot of traffic that turned out to be multicast. The additional traffic causing problems with voice. We have been steadily increasing the amout of Apple devices we have. We upgraded the WLC software to 7....
Hi all, I am trying to find some instructions to setup the following - AIR-AP2702I-UXK9 I want to run in autonomous mode and it has come with the combined image. It is currently loading like a unified image, how do I convert it? Brad
dears I have in HQ internal WC and guest (anchor) WC. Users in HQ can access internal network and internet via wireless network using 2 SSID Is it possible to install one AP in a branch and connect the AP to the controller in HQ. then users in branc...
I'm not sure how to interpret this screen, it seems there are multiple licenses loaded that are greater than the 500 supported APs. Can licenses be moved from one 5508 controller to another?
I have a AIR AP1242AG-a-k9 WAP. I am trying to configure and setup. I am having two main issues. From the web browser, when I go into express set-up two thing are happening. First the Radio options are not there. and second Whe3n I set everything up ...
Hi We have a single 2500 WLAN controller that has all our of AP's connected to it. We have 36 AP's in total. We have updated some of our clients to support 5GHz and I need to disable the 2.4Ghz radio on 15 of the AP's (as well as disable the low dat...
Not sure if this is the right group to ask this question, but figured it was the best fit. I need to extend our current LAN to a guard shack to provide VoIP and data connections. Running a physical cable would be cost prohibitive, I think, as it h...
Hi,I just updated to PI 3. Now, old (detected) templates are stored in "Templates / My Templates / Discovered Templates". There are about 500 templates resulting from "AP Authorization".New templates are stored in "Templates / … / Features and Techno...
I have a few of these, brand new, just attached them to the network using AIR-PWRINJ3's. The radios are disabled with the following error: "CDP_PD-2-POWER_LOW: All radios disabled. LOW_POWER_CLASSIC_NO_INJECTOR_CONFIGURED"This is the right power inje...
Hi, how can i get the Clean air Statistics of the Access Points connected to the Mobility Agents (3650)??. My master controller is a WLC 5508 (version 7.6.130). Sw_AP_RegalFSSA0_3#show ap dot11 5ghz cleanair air-quality worst% This command is not...
Hi, We are struggling to get redirect working as it it has been attached some additional information to the redirected URL. Instead of http://<MSE>:8084/fbwifi/forward is redirecting to xx.xx.xx.xx:8084/fbwifi/forward?switch_url=http://1.1.1.2/log...
