Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hello there I bought Aironet 2702e AP from Cisco and i just couldn't configure in a normal way. I try to move to autonomous using tftp and i followed every steps but i just got this error. %Error opening tftp://255.255.255.255/ap3g2-k9w7-tar.default...
Hi, i have using Cisco WLC 2504 with Version (8.1.102.0) and 1832 access point with image (ap3g2-k9w8-mx.153-3.JBB). When i connect the AP with the controller POE port its boot up but didnot associate with WLC. -> I have configured the management in...
Hi, i was checking the documentation on the 2500 WLAN controller... it states "The Power over Ethernet (PoE) ports on the Cisco 2500 Series Wireless Controller will not support directly attached APs." ... if that is true, what are those PoE ports goo...
Hi! I have an issue with my WLC2504 box. After some manipulation of the box : - I cannot reset the config : it comes back to the config I had set in - I cannot use the Console port any longer (?) - the only way to access the console mode I have, is ...
Hi, My 2500 Series WLC has 3 APs connected . One is a wired AP and other 2 APs are connected via PoE. The APs which are connected via PoE are frequently goes down . I have checked the logs . Below I am pasting the logs . Feb 28 09:41:18.061: [ERROR...
Hello! I have a Cisco 2504 WLC with 5 APs and 3 SSID. I have a problem with some users, the WLC disconnects them constantly and when I see my logs I obtain the next error: Thu Feb 23 14:31:06 2017 WPA MIC Error counter measure activated on Radio with...
Hi Experts, I have set-up where DHCP server is located in data centre and my corporate office has got complete local Wireless set-up which includes WLC and AP. I have query about reachability between client and DHCP server for two different scenarios...
Hi, I have a capwap 1702i access point. I have to convert it in automatons mode. I know the steps but issue is that how i can get the configuration mode of access point. I have connected the console cable to access point after booting and i am rece...
Hello, In the WIDEPLOY training they state "you should never mix 802.11ac APs with 802.11n APs. The training materials did not elaborate on this and I now have a customer that is asking why they should not mix them. Does anyone have the exact reaso...
Is there any documentation that describes how to configure the 2nd gig ethernet port? I would like to connect a security camera off that port. Thank you.
Hi guys, We bought few Cisco 8821 wireless phones and trying to add these phones on CUCM. But the phones are not showing in the Phone Type. The compatibility matrix shows CUCM 10.5.2 but the phone type does not appear. Do I need to download the lates...
I want to change minimum data rates, so which data rates should I to change, date rates or MCS data rates?
Hi All My office have bought 3 AP AIR-AP1852E-S-K9. I did configure AP1 to mode: AP & Controller with ME controller IP 10.155.241.5 - AP1 10.155.241.6 AP2 and AP3 to mode : AP only with AP2: 10.155.241.7, AP3: 10.51.241.8 In LAN, we only use static I...
Hi Experts, Can we have MC's and MA's of different version in 3850 switch model? Currently all of our MA & MC's are in 3.6.3e version , we want to perform upgrade to 3.6.6e in one of our MA and see the performance of the AP's associated with that IDF...
I currently have my APs terminated into 3850 Catalyst switches which run as Mobility Controllers. We purchased a 5520 WLC and I wanted to know if there is a way to move the APs over one by one to point to the new 5520 WLC. I ssh'd into the APs and se...
