Im moving a HA pair 9800-40 WLC from location to another. Is it possible to just change the management IP addressing and the failover IPs via cli. I can find plenty documentation on configuring out of the box but nothing on how to move them.I didnt w...
Forum Posts
Resolved! connection reserve within the devices
Hello, Im not sure how feasible what Im about to propose is, but I kindly ask you to listen to me for a moment. Basically, I would like to develop a technique that allows storing a Wi-Fi connection directly in the phone, so it can be used even when t...
I have an SSID configured to use the Endpoint Management Enrollment Splash Page with SAML enabled on Systems Manager network. I am using a walled garden to allow access to MS login pages and gooogle/apple play store for download of Systems Manager ap...
In the AirOs system, on the 5520, the Network Spectrum Interface Key is found on the wireless/general page. However I can not find the key for devices attached to the IOSxe on the 9800..has that bit of Clean Air been removed in leu of all the new t...
mportant noteWi-Fi 5 Wave 2 MRs support - This version and subsequent MR 31.x.x are only supported on 802.11ax (Wi-Fi 6) and newer MR models. 802.11ac Wave 2 and older products will only upgrade to the backup version (MR 30.7.1) if they are in networ...
Learning objective Identify AFC features and how they optimize the network for compliant, interference-free 6 GHz wireless. Learn Meraki’s wireless AFC optimizes 6 GHz spectrum usage, automates interference management, ensures regulatory compliance, ...
Resolved! Cisco EWC multiple sites ?
Hello,Is it possible to create multiple sites (Configuration>Wireless Setup>Basic) on a Cisco C9120AXI running 17.12.3 code ? The Add button is missing so I would like to verify if the limit is only one. I created one site successfully (see attached)
Hi community,I could not find much info on this topic and therefore I am posting it here to see if somebody can help me with it. I am quite new to Meraki so it might be the case I am missing a silly config.Problem: I am working on a lab (MX -> MS -> ...
Hi,I'm working on a hospitality opportunity and in the solution I added the MR36H, my question is what would be needed to interface their present Opera PMS, Thanks
Hi,How can I integrate Cisco Wireless 9800-CL with OKTA 2FA?
Been configuring a network in Cisco Packet Tracer to learn how to use WLC, but despite following the instructions i've been given, it just doesn't seem to work no matter what, wireless devices just don't see the access point. See provided zip folder ...
Resolved! cisco vwlc ap join problem
created new virtual machine with 8.10.196.0 version. but when ap try join wlc can download image from wlc.*Mar 3 09:32:25.255: %CAPWAP-6-AP_IMG_DWNLD: Required image not found on AP. Downloading image from Controller.*Mar 3 09:32:25.259: Loading file...
Resolved! Migrate 9120AP on EWC to meraki
Hi AllI have a Cisco Embedded Wireless Controller on Catalyst Access Points running on ISO version 17.9.4.27The AP model been registered to the EWC is C9120AXI-KWe are looking at licensing it the devices and migrating them over to Meraki. I am curren...
Hi, I have the WLC C9800-L-F-K9 . The Aps AP C9115AXI-E and AIR-AP1562E-E-K9 are not getting registered to the WLC.The Ap is pingable from wlc and WLC is pingable from AP. On console, I am getting teh below logs. ipv6 gw config loop in discovery time...
Dear TeamWe have done 8 ap renewal purchase, I got 2 pis license out of 4. I have renewed the first license, my 4 ap has been renewed, I am going to renew the remaining 4 ap but it is not allowing me to renew the remaining 4 ap, it is extending the v...
