Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi All, I have configured DHCP scope on WLC. I am little bit confused, on interface configuration which IP should be configure for Primary/secondary DHCP server. Thank you Gaurav
Instead of me writing a whole post again I found another individual on expert's exchange who is dealing with the exact same issue as us. We just recently purchased a couple new 3650 48PS-S switches and (3) Aironet 2702i's APs. Signal strength in th...
Resolved! vWLC Installation on physical machine
I was planning to install a virtual wireless LAN controller on a physical machine.But I failed to install when i enter the “bash” mode look like a linux user-interface. I wanna know if vwlc has to be installed based on vmware environment?even if I us...
We installed 10 Cisco 3600i AP's, into one of our new buildings. The AP's are connected to a 2960S PoE switch. The 10 ports are configured for auto power inline. The ports show 15.4 watts. For 8 of the AP's, Radio 0 802.11 b/g/n admin status show...
Hi all, I have come across a potential issue regarding the web auth and http server on the 5760. We are using one of these as a guest anchor controller with web auth. It initially worked fine with a small scale user count (20-30), however, on scaling...
I'm sending a GET request to retrieve RFID Tag location information - /contextaware/v1/location/tags API - and it appears as if the VendorData is limited to 128 bytes, it is also base64binary encoded. If my Tag has a vendor data payload of more than ...
Hi Guys, Just as the title saysCorrect me if Im wrong:Both TACACS+ and RADIUS can be used for management access to WLC right? Well how about for LDAP? (Actually my answer to this is "not possible" but I just want to make sure)Soo, is LDAP for managem...
Good morning, In one of our sites we have 2 Catalyst express 500 that are responsible for the LAN switching on that local. We only had there one access point till now one old Aironet 1240AG that worked perfectly connected to the switch with the smart...
Hi GuysWe are deploying an Anchor Controller (2504) to terminate our Guest SSIDs. We are using new mobility to support a mix of 3850, 5508 and WISM2 controllers. SSID1 (Guest) - Open with Layer3 Web Authentication on Anchor controllerSSID2 (BYOD) - ...
Hi, I have a situation where wireless clients are not able to resolve the Layer 2 address of their default gateway (I can see this via an arp -a command on a wireless client), this is on our guest SSID, the controller sits in the DMZ along with the g...
hello,I have a hardware-failed device Cisco 2106 from which I have the configuration. I have a new 2106 device. Is there a way to move / import / copy the old configuration into the new 2106 ?Thanks PS I have the show run-config commands
I'm running version: 8.0.120.0 and would like to know if there is a way to manually change the hostname without using the setup wizard?
Resolved! mesh firmware Cisco AIR-CAP2602I-E-K9.
hello,we have a couple of access point Cisco AIR-CAP2602I-E-K9 that are configured as lighweight access point.can we convert these access point to mesh firmware ?We need to configure these access point in Bridge mode as RAP or mesh access points as M...
Hi All,We are facing some weird issue after applied the initial configurations and first reboot in our MSE 7.6. Even we double checked and corrected our NTP settings. Additionally, we disabled the system cryptography to use FIPS. All looks fine, howe...
Hi All,Got the title error when adding an AVC rule to a profile. My device is WLC 2504 on software version 8.1.102. I know the AVC feature is working fie on previous 8.0 software. Do you know if this feature had been removed or this is just a bug in ...
