Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi,Is the Cisco 3700 WLAN Access Point supported/powered by Cisco Aironet Power Injector Media Converter AIR-PWRINJ-FIB=
Resolved! Flexconnect only works on Native VLAN
Hi, I was planning on using Flexconnect for access to local resources on multiple WLANs/VLANs. I connect an AP to a trunk port with Native VLAN 600. The AP is configured as a Flexconnect AP and under the Flexconnect tab I configure the Native Id and ...
Hopefully a nice simple question but in AVC what applications do I need to add to my AVC profile to give priority to Google Hangouts?I had hoped it would be nice and simple like Google Hangouts but apparently not. I'm running 7.6.120 software with AV...
Hello i am from Venezuela I have AIR-CAP1702I-A-K9, but i cant access it through console,ssh, telnet, i know that there are two firmware:1) Autonamos2) Lightweight I bealive that my AP 1700 comes with Lightweigth, but a i dont have any controller, s...
I have configured an AP using FlexConnect but clients get disconnected from it. When the AP was first configured and integrated to the WLC everything seems to be fine but after a while clients started to got disconnected. I reset the AP to its factor...
Hi Everyone, Is it possible if i have single WAP and WLC to setup 2 SSIDs one for internal users and other for visitors?Also i want that internal and Visitors should be on different subnets?Regards Mahesh
I have two Cisco Aironet 1042 AP that are set up to use a WPA2 key, (which is 32 characters and hard to type and not easy to remember), to connect to them. I have a RADIUS Server running on a Windows 2008 server that I would like to use for authentic...
I have a 5508 WLC in the states running 7.6.130 firmware. I am deploying six APs in Great Brittan. The APs were able to draw option 43, find the WLC, download firmware, and register under default local mode. When I change an APs mode to FlexConnect...
I Have a 1532i and have configured if for autonomous mode got everything working with the survey ssid I need.The signal strength that I have from it is very poor all setting for transmit power are set to max but still very poor I have a 2600 which is...
Resolved! WLC 4402 interfaces and config
Hi Everyone, I got 4402 WLC and was trying to configure it.IT has 4 interfaces service,utility and 1 and 2. Service interface has default IP 192.168.1.1 and i tried to use this interface to confiure the device but i was unable to ping the WLC.Need t...
Hi,i have a Cisco Virtual Wireless Controller 8.0.115.0 .I want to connect a cap1702 but i have the message " Power Type/Mode: PoE/Low Power (degraded mode)" .So, i connect this ap to AIR-PWRINJ5 (according to the datasheet) but i have the same error...
Hello my friends, I have AP aironet 1240ag , i tried to configure it but when i finished it doesn't work ,so i noted that there is an error with mac address , and as you can see there is no mac address or the mac address is "bia" and it's immpossibl...
Hi, we are using CISCO 5508 WLC and got High latency between PDA and Laptop in the same SSID and VLAN, latency is around 300ms...but between laptop, the latency is 5ms. May I know what can cause this problem? thank you so much indeed.
Hi,Does the Cisco Virtual Wireless Controller support DTLS??
Hi,Is the Cisco 3700 Shipped with a Power Block AIR-PWR-B=
