Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
We have two 5520 WLCs setup for HA. The secondary unit just keeps rebooting after peer discovery with the following: Rebooting system due to Standby IPC failure. Any ideas, not getting anything searching the web. Thanks!
Hi Experts , Need help with the respect to understand the best practice to place/create the DHCP scope for remote site Guest SSID which will be connected to HQ Foeign-Anchor controller set-up. how about internet traffic for Guest SSID , which one wil...
We have a 5508 WLC managing 45 access points distributed across our 15 offices. We have 3 SSID's configured on all access points and have QOS setup across 2 of these SSID's. The issue we are facing is that we have different WAN bandwidth at each of t...
Hi Guys,I'm not sure what is the best solution to configure a Workaround for a passive Client.We have wired Clients behind Workgroup bridges (Siemens) with static IPs.Additional we have configured AP Group.Since passive Client together with AP Groups...
Hi all, New to the forum. Posted in small business wireless not sure if that was the right group so I posting here I have a Aironet 1602E running IOS Version 15.2(2)JB2 I seem to be having a problem in that the software is up for the port but the har...
Hello all, I have a situation where a client is undergoing a major site network overhaul and we are in the process of establishing a new installation with 5520 WLC. However, the current situation for the site WLANs is not the most optimal with scarce...
WLC 8500 with 8.0.120.0 I installed one 1572EAC-M AP on power injector. When I check the power level allowed it's only 3 levels "16, 13, and 10" The WLC "show country channels support tx-power" it allowes me to use 27dbm on certain channels, why can'...
Hi, If a room can accomodate 100 people and we assume that everyone use 2 device atleast and they use youtube streaming and skype calling How can we plan this wlan ap is 3702 Thanks
Aironet 3800i Not showing SSID in FlexConnect Mode We recently deployed the 3800i APs and some APs work and properly show the locally switched SSID, but the majority of the APs do not. We have checked our switching and everything looks good. Any sugg...
Hi Team, Want to know what is the limit of the mac address addition in WISM-2 with 8.0.120 version, Currently we have not able to add the new mac address in the mac filtering tab. our mac counts is 2029 , so is it the limit , is there any other way t...
Hi All, I am facing one issue related with Cisco Autonomous AP 2602i which is running IOS v15.3(3) JD. Although 8 APs are implemented, 2 APs are rebooted themselves very frequently. I don't know how to solve this issue and couldn't resolved it so far...
LAB Scenario: Virtual Wireless LAN Controller = 8.2 Cisco Prime Infrastructure Virtual Appliance = 3.1 Cisco Mobility Services Engine Virtual Appliance = 8.0 AP = AIR - CAP3502I - C - K9 Issue : I want to configure web authentication, if any user con...
Hi Expert, I have a problem to join AP1523E to WLC2504. I already configure the WLC and put the MAC filtering list of AP's. For the Switch, I already configured port for WLC is "switch port mode trunk" and for RAP switch port as "switchport mode acc...
Hello, I have just realized that the C3750 switch only seems to support 15.4 watts per port which isn't sufficient for the AIR-AP2702E-UXK9 to run a full power Any help with increasing this would be very helpful, thank you in advance. Ed
Hello! WLC 5520 has not HA-SKU unit. What license should I buy if I want to use a second controller for secondary N+1 unit? Do I have to buy 2 x AIR-CT5520-50-K9 or 1 x AIR-CT5520-50-K9 and 1 x AIR-CT5520-K9 and use AIR-CT5520-K9 as a secondary? The...
