Wireless

I have a new dell xps 15inc with the dell 802.11ac wireless card but it will not connect to the Cisco 1250 AP, however it connect to other APs just fine. I wondering if the Cisco 1250 AP is just to old and if there is any documentation proving this. ...

In doing testing with the OEAP602I Access Point, I noticed that it is limiting the bandwidth over my wireless connection.  It is currently setup with a CAP/WAP tunnel to our WLC2504 to provide our Corporate Wireless network to my home, but I am also ...

Hi all,I have been asked to configure a WLC controller to have multiple AP manager ports configured. Port 1 connects to a layer 3 switch in one subnet (10.10.10.0/16) and management address has been configured for 10.10.10.1. This interface will be u...

We want  to send information on Client Properties page on WLAN Controller to SYSLOG Server. I mean we want to send information about wireless client (IP addres, username e. t. c.) to SYSLOG Server. How we can do this? Which configuration we need to d...

Hi,i installed Virtual MSE by beplying ova file, and after typed the default username and password and completed the installation process. it stuck as shown in the attached snapshotdoes any one have any idea about this ?

Using  MESH AP 1552E , for designing MESH network and determining parent ,child APs , i want to configure all APs with "Preferred Parent Selection" configuration to make sure that each mesh tree will not exceed 3 MAPs per RAP.How can i check SNR betw...

Hi,We need to implement Wireless network in a Villa - the scenario is: We need 3x Access Points (indoor) to be connected wirelessly with the main AP unit (connected with PoE switch and then Internet router). There is no line of sight for these 3 APs ...

Due to corporate requirement we had changed the SSID from WORK to WORK1 and end users are not getting IP address.We have reverted back to WORK still users are not getting IP address.Where should I look so that this problem gets resolved? 

Hi everyone!A customer of mine has a 5508-WLC. (Version 8.0.110.0, before ist was 7.4.x.x)He tries to establish a VPN connection via Checkpoint client to a Checkpoint Firewall from the internal Wi-Fi. However, this does not state.The whole thing goes...

Hello. i have saerched but could not found.The controller and Access points works fine, but i have a problem like this: when i have a static ip address on cleint device, i can not access anything. when i set ip address to dhcp it is working  fine wit...

Hi I think my router only has 2.4 Ghz broadcast  following is from show controller Dot11Radio 1 command Is there a way to upgrade or add the 5Ghz frequency? interface Dot11Radio0Radio ATHEROS AR5212, Base Address c84c.7519.77a0, BBlock version 0.01, ...

       RADIO0-802.11N2.4GHZ  STATUS     DETAILED STATUS     SETTINGS     CARRIER BUSY TEST     Hostname  ap1ap1 uptime is 32 minutes     Network Interfaces: Radio0-802.11N2.4GHz Settings Operating Mode:MixedEnable Radio: Enable Disable Current Status...

Just got a Cisco 3501 AP, Did not know it required such complex configuration. If someone could/would help out. here is what I am askingI have a cisco 3650 switch NICE- It has the controller for this wireless AP>  I have no ideas how to set that up, ...

Hi, I have an existing setup where in i have a 4400 WLC and AP 1242 registered to it.I had to replace the WLC with a new 5500 WLC. I tried registering the the 1242 AP with this new controller but i'm getting the following error message: AP0026.0b4d.0...

Hi folks I have been trying to figure out why my download speeds are not as fast as I expect.  I have recently installed a Cisco 2702 in place of my Cisco 1041 AP.   I have the AP plugged into a Cisco 1921 router via a non Cisco dumb 10/100/1000 swit...