Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Recovering a hung 2504 wlc
Dear Experts, I have an 2500 WLC, which some how got hung and is not responding. Recently I have upgraded the code on it to 8.0.100.0 followed by FUS upgrade to the latest available one: 1.9. It was all fine for a week, however suddenly I see: 1)W...
hi all ,our primary wlc has failed and we received a new one from rma.Now If I set ha between the new wlc and existing one.will existing wlc push up configuration to new wlc (primary)? release 7.4thanks in advance
Hi,We have installed the new cisco AP 2702i on our new building and we have a bad performance on the wireless network. When I check the AP configuration on the controller I see a strange information, the interface gigaethernet1 is down (no connect) ...
Any possibility a Terrawave outdoor 4 wire/element antenna could be used with a 3502e AP? Have seen some posts about the 3 ports and different antenna options, but not quite covering this type of mix/match. Came across this antenna still in the box...
Curious if there is an actual reason in this day and age why the Cisco 3600 series AP running the latest autonomous IOS, will fully accept, detect and configure the RM3000AC wave1 module but still will not let it advertise SSID. I understand that thi...
Hi,We have installed the new cisco AP 2702i on our new building and we have a bad performance on the wireless network. When I check the AP configuration on the controller I see a strange information, the interface gigaethernet1 is down (no connect) ...
I have have 2x 4404's (2x) and 2x 5508's all are running 7.0.240.0. When I take an 1142 and associate it to a 4404 I can connect a test client using N at 144Mbps and I can get transfer rates averaging 70Mbps (using iperf tests). When I take the same ...
Hello everyone, I plan to deploy about 250 APs in our office. If possible I want to use the vWLC because of its low price compared to a hardware WLC. Since the vWLC is ristricted to max. 200 APs, I am thinkink about to use two vWLCs and put them toge...
we installed a cisco flexvpn solution using cisco 819 with 3g modem as spokes.in order to limit the costs we would like to disable the roaming feature on the modem.is it supported? if yes how?thank you
Hello Friends, It is again a conceptual question.In Flex-connect Local Switching mode if the Client has to be get the IP address using DHCP, the DHCP server has to be local to the remote site and not centralized location. Though i know, Local switchi...
With Gilles DufourMonday, January 19th, 2015 to Friday, January 30th, 2015 Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about how to configure and troubleshoot Cisco 3GPP Mobi...
I would like to deactivate or remove the eval ap license on my WLC 5508 for being able to test a HA setup on a WLC with 0 licenses.Is there a way to get rid of the eval license while it is active?In the command reference guide I found the 'license cl...
hello,we are facing an issue that our wireless lan controller (5508 with version 7.6.100) doesn´t mark management frames (e.g. reassociation repsonse - necessary for roaming) with CS6. therefore some of them are dropped leaving the clients not to roa...
HelloIs there a way to change an AP identifier number ? (Cisco Controller) >show ap config general XXXCisco AP Identifier.............................. 336Cisco AP Name.................................... XXX thank you
Standalone ap connects to switch in vlan X. so we configured the BVI interface ip as x.x.x.x.Now we need to create a DHCP pool for ip range y.y.y.y which is not created in switch side as any vlan.Whether it is possible?ip dhcp pool testnetwork y.y.y....
