Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Good Afternoon, I am trying to setup my 1220b. I tried using dhcp. I've tried using hyper serial port and console cable. the cable connects, but i am not able to bring up any configure pages from ap. I do get the ap> when communicating. is there any ...
HeyI have Verizon FiOS at home. When I run speedtest on my LG G2 phone with wireless turned on, just up the steps from my wireless Actiontec router (running CAT 6 and not BNC), I get ~1 Mb/s up and ~1Mb/s down though I have the 5/15 plan. When I tur...
Dear all,We have vWLC, AP connected through MPLS network, we also have ap base license for 15 AP, the problem is that AP cant joint to WLC because ofthis error:Maximum number of AP supported has already joined ciscoWLC shows that all 15 licenses are...
I have a Cisco 5508 with 25 licenses. It shows that all 25 licenses are in use, but only 16 access points are active. I suspect that the controller still has old/inactive access points using a license. How can I reclaim those licenses for new/repl...
Hello, I'm managing a large number of access points on a Cisco wlc 5508 controller.We've recently purchased a bunch of new AIR-CAP1602I-E-K9.note that we already have AIR-CAP1602I-E-K9 and other models in production. These A.P are not able to join th...
HICan anyone guide whether we can use 2700 series access points in stand alone mode if we had purchased controller based access points and secondly if we buy controller based access points, can we transfer it to stand alone mode and use it separetly....
5760 WLC has default session timeout as 1800s. The laptop running window 8.1 was authenticate using EAP-TLS. It was successfully associated with wireless network, but every 30 minutes (1800s) the client session dropped out. It is expected the client ...
Resolved! wireless printing
I have WLC 5508 running software version 7.0.235.3. I created an SSID with WPA2 PSK encryption TKIP. I verified both wireless printer and iPad are connected to the SSID and have an IP address. The HP printer's firmware is up-to-date and has Airprint ...
Good afternoon,We are unable to connect any version of ipads to our production wireless. The SSID is not broadcasted. We are using WPA2 with AES. We have a guest network on this WLC that has a broadcasted SSID and we're able to connect the iPads t...
hello all,i'm sure the creation of guest accounts on the lobby admin page is a painful process for all involved - for us, it involves a process like this:visitor asks for wifi > receptionist phones IT > IT creates account> IT phones receptionist with...
Hello Experts,Need your suggestion, though I have gone through some documents the solution does not work as per my requirement as below. Still to confirm.I wants to use LAP in flex connect mode & standalone access Point to act as WGB. However, as my ...
I know the WLC can be integrated with the old Cisco IPS.With the new Cisco IPS, specifically Cisco Firepower, does it still work with the WLC ? If so do you know of any design or documentation? I'm running on ver8.0 and looking to purchase the Firep...
Resolved! Directional Antennas for CMX analytics?
Hi there,I am in the process of planning AP placements for a large scale outdoor CMX Analytics project. Unfortunately the client that owns the outdoor space, does not own the buildings that run parallel to certain areas and RF bleed to nearby busines...
Hello all,I have a customer that is currently using Cisco Wireless gear and is wanting to go to Cisco FlexConnect within their LAN.From my research it says FlexConnect is geared more towards WAN deployments where you want to minimize the amount of co...
I have multiple wireless access points plugged into a 3560X. When the wireless clients begin roaming they cause duplicate MAC enteries to be created and this causes the switch ports to flap. Is there a way to configure the switch to either ignore t...
