Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi Folks, We have an WLC 5508 where our 1st AP is connected and its working fine. Unfortunately i cant lay cable , that's why want to use the other 2 AP's as an Repeater so that it can Broadcast the same SSID as the 1st AP broadcasting. How can i do ...
Hello, I am very new to the Cisco Aironet 1140 AP. I am trying to configure it the best and easiest possible way. I want to have two SSIDs one that is for the guest network with only internet access but still having a password. No internal access to ...
Resolved! WLC 5508 do not Join CAP2602E
Dear All, My WLC a 5508 version 8.0.100.0.Do not Join a CAP2602E, is the first time that i connect this model of AP to the WLC.I have enabled some Debug and I see that on the controller I got the "Unknown AP type. Using Controller Version!!!" error o...
I have a client that has a Chromecast, with a 1010 and a 1130 Autonomous access points. I can not get the Chromecast to work. Can someone tell me how to enable mDNS, or Multicast on these access points?
Hi everybody,I am asked to install a Cisco WAP200E Wireless-G Exterior Access Point into my company network infrastructure.But there is an issue that I would like you to help me to solution it.In fact the AP mentioned above is a PoE device, and our S...
Hello everybody,I have a problem to modify the field "location" in an access point on WCS.In fact, when i try to modify this field and then apply the modification, i have this error message : "Error(s): You must correct the following error(s) before ...
Hi,Im trying to add a cisco wireless access point AIR-SAP2602I-E-K9 to my wireless Lan controllerthis is the basic info from the WLCProduct Version.................................. 5.1.151.0RTOS Version..................................... Linux-2.6...
HI Team , this is a peculiar issue started recently that few users were not able to get authenticated to wireless using there mobile , parameters checked DHCP scope is sufficient no issues founduser AD id's are added for authenticationplease help ...
Resolved! NCS import web management certificate
Hi,I have some trouble uploading a certificate in NCS.When I upload the certificate it says:XX-XX-NCS01/admin# ncs key importsignedcert wlan_xx_xxxx_nl.pem repository ncs-tftp-repo INFO: no staging url defined, using local space. rval:2The WCS...
I'm tconfiguring a new Aironet 1142 wireless access point with the webconfiguration utility. I only need a simple single SSID, no VLANs, and aWPA2 autentication password (I can't let it with a 128 bits wep passwordbecause the ap is for normal random ...
Resolved! air-sap2602i-n-k9 <=> air-cap2602i-n-k9
I want to order two autonomous.What is the different between "air-sap2602i-n-k9" and "air-cap2602i-n-k9"?
I would like to convert AP in order to register it to AIR-WLC2112-K9.By now it has the following software:cisco AIR-CAP3502I-A-K9 (PowerPC460exr) processor (revision C0)LWAPP image version 7.5.1.53System image file is "flash:/ap3g1-rcvk9w8-mx/ap3g1-...
Setting up a new 5508 controller with 2702i APs and I am trying to configure flexconnect for the APs located in three remote offices. I have one SSID that will be the same at all sites and have the option checked for local switching on this WLAN. Th...
hello, hello ,please , I need help urgently.I have a 5508 WLC , a Switch 2960 and 2901 router is call manager .I want to configure two networks:SSID 1: For the data for PCSSID 2: For IP phones WIFIMy problem is that I can display the SSDI 1 and I can...
Hi, I am configuring GRE over IPSEC tunnel vpn between CISCO ASR 1000x & Juniper SRX210. After configuring the tunnel is up from both end but not able to communicate between tunnel. Even can't ping tunnel IP from both side. I am attached the config f...
