Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi,Is there some way easy to view how many GB a client have used?On my old setup (AP2802 mobility express) I had on the frontpage dashboard a view saying how many GB each client have used.On my 9120 setup (embedded wireless controller) I have to go t...
Format: Log Type - Time(microsec) - Message - Optional InfoLog Type: B - Since Boot(Power On Reset), D - Delta, S - StatisticS - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00163S - IMAGE_VARIANT_STRING=HAACANAZAS - OEM_IMAGE_VERSION_STRING=CRMS - Boot Con...
Hello All,We have been thinking about improving our guest and byod wifi access to accommodate multiple use cases.One of the main goal for the new solution is to cater all connections using single SSID.We are using Cisco 9800 wireless controllers. In ...
I have a WLC 2504, but I don't have the credentials to access it and I'm looking to reset it to factory settings. However, I don't have access to the console because the BAUD rate and console port parameters were changed, so I only see strange charac...
Hi,I am confused with Cisco explanation about how TPC works, especially TPC hysteresis. Cisco says that:If Tx_Ideal is higher than Tx_current, then a power increase is recommended. If Tx_Ideal is lower than Tx_current, then a power decrease is recomm...
I have 50 WAP connected to a WLC 5508. When I backup the config I don't see the custom settings I put in some WAP. Where are the WAP settings saved at ?
We have a guest network setup on WLC 9800-40 version 17.12.2 with ISE (3.1)as radius server. Central web auth is configured with self registered user. Captive portal loads fine and registration of new user is fine.However after login with credentials...
Hello,Is there an easier way to view how many GB a client has used on a 9120 setup (embedded wireless controller)? On my old AP2802 (Mobility Express), the dashboard showed usage data for each client directly on the front page.With the 9120 setup, I ...
we have 2 wlc, 9800 & 3504.a wlan is deployed with same configuation from both wlc to 2 buildings.wlan using 802.1x authentication by same nac.user move from building a to b will suffer wifi connection failure at first several minutes.nac got no auth...
Cisco 9800 Client session data realtime (8540s had enhanced traps)is there a way on the 9800s to gather realtime client session data when deauth trap (i dont see it working when enabled in the snmp wireless traps section.)8540s had this (but i cant f...
I have a virtual wlc C9800-CL, I can access it via SSH and HTTPS from WAN, however when I am on-site connected to the wireless and trying perform a SSH/HTTPS the WLC is not responding. I did a wireshark capture on the WLC, and I notice the TCP SYN pa...
Is anyone here using group policies to set different VLAN tags, per client, on the same SSID? For example, I have the following:ssid: foossid access control vlan tag configured: 105mode: bridgedauth: basic psk wpa2vlan 105 network: 192.168.5.0/24vlan...
Hi Everyone, I have three cisco AIR-AP2702I-UXK9 model access points. None of them are responding to the console access.Same console cable works for 3750 switch and other routers but when connected to the access point they just dont respond. Just for...
Resolved! C9130AXI_E stuck downloading image
WLC 9800-40Software 17.9.2Hello, we have a problem with ap's not joing the controller.Tried a factory reset, and we log the following:Any suggestions ?[*02/10/2023 11:04:27.9330] Reset chip in progess, not resetting[*02/10/2023 11:04:28.0865] DOT11_T...
Hi,We’re using Cisco Air-AP1815i-I-K9 access points, which are connected to our network and managed by a controller of the same model. We’ve configured the RADIUS parameters in the WLAN (SSID) settings, and when testing the controller with our Micros...
