Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I have broadband internet at my home and im using cisco linkys e900 router. I use this wifi on my one desktop, one laptop and 2 android phones. Issue i'm facing is only with the m2 note particularly with my wifi. Problem is such i'm experience slow l...
We recently had a wireless flap event thanks to some techs in another country amending DNS entries, and we noticed that roughly half of our AP's in Flexconnect (local switching) mode eventually went into rediscovery. We are trying to find out what ma...
I have a Cisco wireless controller 2106 (AIR-WLC2106-K9). With 4 AP's connected, all are AIR-LAP1041N-A-K9 , 2 locally and 2 at a remote site. Any time there is a power failure, network connection down, backup generator test activated, the local ...
I have a non ciso DSL modem with wifi enabled and I have a CIsco AIR AP 1231G device as well. Is it possible to configure the cisco AP and the repeater by using the non cisco DSL wifi device as parent ? I tried many ways but in the log of cisco devic...
hello,does someone can give me the command on a wlc to pre-download the image on an AP? Then, to reboot it in Primary on backup Image? Tx B
Im working on a case where an AP is allowing only a certain amount of users to successfully access the AP. the AP was working correctly and good until just recently. users can associate just fine to the AP however the access to the internet is restr...
I have the following business requierement: I have 3x WiSM2 on Slot 2,3 and 4 on a 6509 Chassis 1 and the same setup for a second 6509. Currently I have 6 active WLCs on the network. The requirement is to add HA and make 3 active and 3 on hot stand-b...
Hello All, I am going through Cisco ClearAir implementation documentation and there are few terms that confused me. a. What is the difference between Mobility Agent and Mobility Anchor? b. Can we use Cisco WLC5508 as Cisco CleanAir Mobility controlle...
Hello, when you have clients connected to a wifi access point and they are communicating outbound, which MAC address is used for the source address i.e. the MAC address of the client or the MAC address of the wifi access point itself ? Thanks for an...
I have one SFP connector, I plug into the switch, now can't take out, I try to pull out, but fails, how to take out? thanks
Hi Community, I'm working with CMX 10.2 and when I started to gather documentation I found that in version 8.0 It was present a functionality called Alternative Path Analysis where you could have a view on the map about the percentage of paths took b...
I am looking for an explanation of an error message I am receiving in my syslog from my cisco 5508 running code version 8.0.121. The syslog message is "#LWAPP-4-DATA_PLANE_ECHO: spam_lrad.c:36940 AP AP(apname) reported timeout communicating to contro...
I use WLC as internal DHCP server, pool is defined, but when I double click the SSID: test01(internal WLAN SISD), it can't establish the connection config is attached, in the switch side, I didn't setup 10.10.32.254 and vlan 32 how to resolve my prob...
Hello Experts,Hope all are doing well!1. In a deployment there were 2600 series AP & now client ordered 1600 series AP. In one floor both the models are deployed, now interesting is 1600 series does not support clean air & 2600 is with clean air will...
I’m having a problem with our 7921 phones in our test production lightweight wireless network. In a lab environment with an Autonomous AP I can make them work with the 2811 router running CME but when I take that same CME configuration to production ...
