Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Greetings, I am looking for some guidance regarding peer to peer isolation using multiple aps with local switching.I am using a EWC with four APs and am looking to implement some form of peer isolation. I understand that it will work as is for device...

Zaku1987 by • Frequent Visitor
  • 5267 Views
  • 9 replies
  • 0 Helpful votes

Hello,is it possible to use the C9120AXE-x only with an single band 5 GHz antenna? Would like to use a 5 Ghz only 4 feed antenna. Can I connect all 4 four cables to the 4 front connectors and it will work? In the documentation I only see dual band 2....

Hydralein by • Community Member
  • 1855 Views
  • 7 replies
  • 0 Helpful votes

Hello,FlexConnect Local switching mode with x3-SSID WPA2+PSKNon-cisco Bridge device and PC are static IP address configured.C9800 <--> [Core Switch] |<--> [Edge Switch] <--> [C9115] ))) ... ((( iPhone/NB are working fine.                             ...

formosa by • Community Member
  • 2046 Views
  • 10 replies
  • 0 Helpful votes

Hi All, trying to deploy vWLC in azure, when the VM is deployed it show error "vm agent not ready". WLC is reachable on network and am able to have CLI access. not getting access via webui though the public IP is reachable (i can ping the public IP)....

I am having to go through and create many Apple IDs with my Apple iPods & iPads when setting up with Meraki MDM. I am just wanting to know what others out there are doing in this case with iPads/iPods and the Meraki MDM.A little info on what I have t...

xvang1225 by • Visitor
  • 19095 Views
  • 10 replies
  • 0 Helpful votes

Hi All I had a brand new 2802i which had an issue with booting up. It only showed the green LED flashing. After attaching a console and booting it again, I saw that it landed in ROM mode. I might have accidently unplugged it while it was booting up t...

patoberli by • VIP Alumni
  • 34546 Views
  • 17 replies
  • 21 Helpful votes

Looking for any insight into a possible migration from Ruckus APs (R710) and Brocade switches (7250) to Meraki.We use Meraki MV Cameras and evaluating Cloud Controller for Ruckus vs possibly moving over to Meraki switches and APs.The main con is the ...

EJN1 by • Level 5
  • 10294 Views
  • 12 replies
  • 0 Helpful votes

Hello, I have set up a Cisco AIR AP2802E with Mobility Express. It also gets an IP and the LED is constantly green. However, I cannot access the website. I keep getting the message in the browser that the connection failed. Does anyone know why this ...

LucaAPnew by • Community Member
  • 1739 Views
  • 6 replies
  • 0 Helpful votes

So for a long time already I'm considering to change the authentication from WPA2 to WPA3.But, I keep reading here and there, that user's are having more issues with it, or are affected by this change to the worse.Any reasons why it's recommended to ...

roeyleon by • Level 4
  • 4564 Views
  • 3 replies
  • 0 Helpful votes

Team,We have configured Cisco ISE with MR46, but when I try to send a session reauthentication request or termination, it does not go through. What could be the reason?Once a user is authenticated, I cannot kick them out of the network. I'm not sure ...

image.png image.png
ankitohc by • Spotlight
  • 3382 Views
  • 5 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card