Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Wism Bulk disable ssh
have controllers with software version 7.0.250.0i found that config ap {telnet | ssh} disable Cisco_AP is only good for specific APhow do i bulk disable SSH for all All APs? thanks
Hi All, I have all my switches configured to run on native vlan 500 and management on vlan 10 with the cisco access point , if I make 500 native or another word trunk untagged vlan then I can't access the router using the BVI interface which is me...
Hi Everyone, WLC is configured to allow visitors access to the internet sites.I need to create webauth if user opens browser he should be redirected to login via RSA auth using Radius.What IP should i use for this webpage?Can this IP be different f...
Resolved! WLC 5508 IOS 6.0
is it possible to manage AP's over WAN with a 5508 running IOS 6.0?If so can you point me to where I can read this config item in the 6.0 config documentation. thanks
Dear Team,I have been looking to find the Cisco Access Points that support both:WPA2-EAP: Encryption: AES, Authentication: IEEE 802.1XWPA2-PSK: Encryption: AES, Authentication: PSK (Pre Shared Key) with more than 21 Characters, combined with MAC addr...
Resolved! WLC with AP's in local mode & Mesh mode
Hello guys,I'm studying for my IUWMS, I'm reading the quick reference and in chapter 5 it talks about Mesh network, but I'm not sure if with one WLC can I have AP's in local & mesh network simultaneously.Anyone can help me with this question?
HI,Before, I had problems about connecting AP to client PC.I had searched for the AP Log.I had to change settings (Max.Data Retries ). and I solved.Recently, I converted cisco AP from autonomous to lightweight.Let me know how to set up such Max.Data ...
Can I do a flexconnect for a small office has local Internet connection? All company applications are centralized at a remote datacenter but not Internet access. Thanks,
Hi all,My Prime Maps does not show a heatmap for one of 3 new Access Points.I deleted the AP from the map and replaced it once but still no heatmap.The AP is active. In the heatmap settings, the AP is selected as well.Anybody any idea whats wrong her...
HelloI tweaked on my controllers a few RRM parameters listed under Coverage Hole Algorithm.Also under TPC a few parameters. There I changed the Transmitted Power Threshold to -72 and the Minimum Power Assignment to 8.Also I updated the controller fir...
I have been trying to configure my 1941w for weeks now. I think I'm close to the goal but this last part has given me issues for week. I have 3 SSID's and 3 VLAN's configured on the AP. everything is configured on the router and ap to work as expecte...
Resolved! AIR-CAP2602E BTU value
Hello, I am looking for the BTU value of AIR-CAP2602E. In datasheet I can not find it.
hi all, how can I configure POI (point of interest) in cisco MSE ??I faced this problem when i configure the CMX feature thanks in advanceappreciation@leoleo
I am trying to create a wireless solution with 3 sites, and one datacenter each remote site have vlan 10, 11, 12 mapped to following :controller sites in datacenter.REMOTE SITE 1vlan 10 - AP management 10.10.10.0/24Vlan 11 - SSID STAFF ...
I have just come into new employment and have inherited a large wifi network. I am used to other wifi vendors so I'm going to ask some rudimentary questions.I'm dealing with 50+ 1142's with users primarily using the 2.4ghz band. It was interesting to...
