Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi thereI have set-up a Cisco AP1142n as a WDS AP and my SSID is using EAP-TLS certificate based authentication. My users rely on a VPN connection whilst connected to the SSID. I am finding that the current roaming functions are not good enough and t...
I would appreciate your suggestions on how could I restrict access on our guest SSID. I have been thing to use web authentication creating users but I need ensure that each user would be able to connect on one device only. I don't want that a guest ...
Hi, Our Setup is as explained belowCisco Wireless Controller with Configured Cisco ACS 5.3 as Radius ServerCisco ACS 5.3 has been integrated with AD for Wireless AuthenticationWe have Primary and secondary Servers which running on cisco acs 5.3.0.40...
Resolved! Redirect Webpage issues
Hello Guys,I have setup guest SSID and user can connect to Internet, when the User connect to SSID they get the IP from DHCP and for internet they need to go to authtication page and administrator give internet acceptance. Now the problem is Users ar...
We have 4 SSID configured on our WCS 7.0.164.3. The last SSID signal strength is not as good as the previously configured SSID, why?
I interested to deploy cisco ISE to my network.that consists many catalyst switch (4503-E,2960G,2960S) and 3 of cisco ap. (2x1600,1252)but other than that 3 cisco ap, my network including other vendor ap,such as 5 of asus DD-wrt based ap, dlink ap an...
Hi,I've seen that the 2504 can be used as a guest anchor controller from release v7.4 onwards but can't find anything to say if it can be used as anchor when a 5760 is the internal controller.Found an older page which references:Q. In centralized mod...
hiam tryin to convert a 1242LAP to 1242AP but am not very clear with the process. i am tryin to follow a document from cisco but i don understand something about it.i give my pc address 10.0.0.3/24connect the LAP to the laptop using ethernetremove th...
Resolved! How to setup 2 1600i ap's
HiAt my current place of work, we have a standalone guest wirleless network powered by adsl with 2 1600i SAP access points. However, only one is working, and try as we might, we cannot get the second one to run. We have tried running the same config ...
HiI have 5508 Cisco WLC and i want to connect my wlc one port to fortigate (FW) for direct internet.And other port in WLC i will connect on Cisco Core Switch for other SSID's and for management. Now the question is how to divide port in WLC 5508, how...
Hi Experts,Is the Cisco 1552e in LWAPP mode supposed to support wIPS? The option is greyed out on my 2504 WLCVersion 7.4.100.60AIR-CAP1552E-N-K9
Hello,I have WLC 2500 with 6 AP updated LWAPPsince Jan, 2014, there were 2 APs frequency made following message in log of WLC:May 5 00:24:46 x.x.x.x kernel: wlc-2504: *spamApTask5: May 05 00:24:46.647: #LWAPP-4-DATA_PLANE_ECHO: spam_lrad.c:31095 AP ...
Hello everyone, I was hoping some of you could give a hand with this: I'm designing a wireless solution for a beach hotel and I want to be sure we will be using the best AP <-> WLC combination and that my design works for indoor AP's too. ...
I'm trying to interpret output from the 'show dot11 statistics client-traffic' command in autonomous IOS version 15.2(4)JB4 on a 3600-series access point. Finding a detailed description of each data point being reported has been very difficult - c'm...
There are two schools of thought. We used to stack access points when we had identical floors of a multistory building. Then along came the theory that you should not stack them - you should stagger locations when floors are the same.How does that...
