Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi Team; I am setting up a bridge connection with 1262 AP as the root and 3502 as the non root and i observed that it is working with only channel 36. If i am setting up other channels like 40,44 & 48 its not working. My partnum...
Resolved! EDRRM AQ and AQI
Hi ; Whats the difference between EDRRM AQ and AQI. If we are setting the sensitivity on the EDRRM to high the value will be 60. Whats the value we are configuring the AQI in the clear air tab. is it only for traps. If i want to change the AP ...
I am trying to connect to our MSE install via AJAX. I can connect and get results for a call via the Chrome REST plugin just fine. But via AJAX i get authentication issues. Any advice? Below is my code with fake IP and user:pass...var url = 'https://...
I have a project to setup wireless internet for guests and employees and i am new to this i have the following questionsHardware we HaveWireless lan controller AIR-CT2504-25-K9 (Cisco 2500 series)Cisco Aironet 1600 series wireless access points (Ante...
HiI have configured snmp on the WLC and I think i do not need to configure snmp on the AP which connected to this WLC. If one AP reboot or fail, it will still send out the trap. Is it correct or I have to configure the snmp on each AP? Thanks Ray
Hi,Maybe someone could help us!We are currently facing a bug with the MSE. Let me explain what's happening.We are using Prime Infrastructure 1.2 and the MSE is using the version 7.3.101.0.Monday, everything worked fine. We are using the MSE with Aero...
Hi everyone, Currently I'm study on wireless. I'm confused between beamforming and spatial stream. Are they the same technologies? Or before spatial stream is running after beamforming was formed? Thanks and Regards,Ong
Resolved! Cisco Prime Device Licensing
Hello, I recently installed a trial version of Prime 2.0. What "counts" towards the license count? Is is 1 for each AP, 1 for the controller(s), and 1 for each switch? I'm not required to license the users correct?
Hello everybody.I'm noticing two of my 30+ APs having the 802.11a radio with "Operational Status = DOWN". The Admin Status is ENABLED, but I don't know where to act to put the op. stat. UP!WLC is running 7.5.102.0, as well as the APs. The affected on...
I just put in a 5508 WLC with a pretty basic setup. I have a Guest WLAN configured that uses authentication with the local user database on the controller. When I connect to the wireless network, I get an IP address from DHCP and my wireless adapter ...
Hi all, I have recently upgraded my controllers from WLC 4404's to some 5508's. We had multicasting configured on the previous controllers for our IPTV solution. Now that we have upgraded to the new WLC's this has stopped working over the wireless. T...
Hi,End user has a WLC 5508 and around 12 LAPs (an increasing un short time) configured and working for mesh network (some ROOTs and MAPs)now is the way to deploy an additional 5508 in another site so that be the backup of the first controller. Tak...
Hi, What is the method to verify what ssid is a mobility anchor group using? We have a mobility tunnel whose one end wlc(5508) will be changed shortly, which will need some changes on the tunnel I believe. Before this is done, we will need to do so...
Hi, I am facing an issue with my AP not joining the controller. Following is the error log Mar 1 00:01:11.923: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER*Mar 1 00:01:21.923: %CAPWAP-3-ERRORLOG: Go join a capwap controller *Apr 3...
Resolved! 7.6 WLC and per user ACL for flexconnect
Hi All,Im in the process of configuring our new 5508 WLC running version 7.6 code with 3700 APs.We run ISE, and have setup our IT Admins to run on a separate VLAN on the wired from general users which works good. This allows us to control who can acc...
