Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello, I've been searching for awhile, but can't seem to find what I'm looking for. We currently use a basic Web Auth setup for Guest Users, mostly for vendors who come on site. Our support department creates usernames and passwords on our Cisco ...
I know someone out there has the answer for this. I am in the process of installing an Aironet 1140 standalone AP. I have not worked with these AP's before. I will be connecting it to one of the PoE ports on the existing ASA 5505. My goal is to have ...
I've been configuring hundreds of 3602i APs via Prime without incident, but I've encountered 2 APs that get to the ap: prompt and doesn't proceed further. If I type boot, then they'll complete the boot process.How do I configure these 2 APs so they ...
Hi all, Please help with the following question : we have an existing wireless network (I'm new to this Cisco wireless) and broadcast several SSIDs. Each SSID is in separated VLAN so how do I find and config certain SSID into a ...
Resolved! AP downgrade when joining WLC
Hello Forum Team! After an access point has joined a new WLC 5508 and upgraded its firmware, if this same ap is registered again to an old WLC 4400 series, does it will downgrade again its firmware and join the old WLC 4400?Tha...
All, Quick question about the association web interface tab on a 1140. I have noticed that the Device Type shows as "unknown" and the Name shows as "NONE." Anyone have a clue as to why? Thanks for any help! Dave
Resolved! Freeing up space in AP flash
Hi,I am trying to free up some space on my 2602i AP. Is there a way to free up some flash space for the autonomous code?I was trying to convert my 2602i to autonomous, but I got this message during the extractingextracting ap3g2-k9w7-mx.152-4.JB3a/ap...
Hi Everybody,We have a FlexConnect AP in a remote site. The AP has successully joigned the WLC 5508 (runnig 7.4.100.0) through WAN connection, and broadcats an enabed WLAN. However client do not receive DHCP leases and then can not connect properly t...
Hi everybody.Two 5508 WLCs running 7.4.100.60. I had to activate HAI decided to configure Service ports: following HA conf guide, I used DHCP. That's because static IPs on service ports are often cleared and forgot during switchove...
Dear Experts,We are in process of deploying ISE 1.2 in our environment for BYOD. The initial step of this process is to configure ISE as an SCEP Proxy and it requires certain configuration on the local CA. We have done all the required configurations...
I need to upgrade WLC5500 series to release 7.4.121.0, but at this moment, WLC manages two AIR-LAP1310G-E-K9, I´m not sure if after upgrade them still work.Are AIR-LAP1310G-E-K9 supported in this version?Regards,EF
Hi,We have deployed some cisco 2602-E access points in one of our clients place. The signal strength found in the laptops is very good, but the signal strength found in the smartphones is very weak and its fluctuating.What is the issue with this and ...
Hi,I am setting up wifi flexconnect solution and is a bit confused regarding what should be the default gateway for the dynamic interfaces which will be created. Will it be the same as the one for management interface or the will it be the one for th...
hi, I have problem with setup Cisco Aironet 702. I set all properties. Interfaces gigaEthernet and Radio0 are UP. I don't see my SSID in network. On properties for Radio0 I see error in section Transmitter Power. How can I troubleshooting this issue...
I can see many neighboring SSIDs in my WLC as rogue SSID and how i can manage this?
