Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Dears all. I have 15 Cisco 1602 Aironet Stand alone Accepoint. I would like to configure this all to work with one SSID with out registering in any wireless lan controller. I would like to get your advice that, what configuration I have to do ?
Resolved! work group bridge with cisco 3500
Hi,We have few cisco 3500 ap's which is to be used as work group bridge. I am not very sure but i think we need the ap to be in autonomous mode to make it a work group bridge. Currently it is running lwapp/capwap image.Is this correct, please help wi...
Hii have a common scenarioLocation-Branch-WLC1-------------WAN/EoIP----------Location Headquarter-WLC2(Anchor in DMZ)----InternetSoftware on WLC is 7.0.230WLC is Model 2504 or 5508 in branch offices and 4404 in Headquarter.Access Points are AIR-CAP35...
I have project where I have 24 Cisco 2602 AP as a wireless bridge. (12 pcs root bridge and 12 pcs of non-root)I would like to use "whatsup Gold" to monitor the RSSI on my wireless links.I have been told that if information is availeble through SNMP, ...
Hi all. I'm very confused about the MAP and RAP mode as they are APs configured in Bridge mode.In the CCNA Wireless, we are clearly taught that Bridge mode APs do NOT deliver client service...Apparently Mesh and Root APs are APs in bridge mode but d...
Resolved! Update Controller IP in Prime 1.3
After updating a Controller IP I am not finding the option to update that information in Prime. It would appear I must remove the controller and add it again. Is this correct or am I missing an option?Thank you
I have a client that is running ver 7.5.120.0 on their controllers and they are having some odd issues, to say the least. The controllers are supposed to be in a HA pair so that one fails, the other one takes completely over. The second WLC only ha...
Hi, I'm trying to setup web auth with a costumized web page on the WLC. Does anybody have a template for a WAP or mobile version of the logn page.Most of the devices that will connect are ipad and mobile phone.Thanks
HiI am trying to backup my WLC (8500, with a HA, running AireOS 7.3.101.0) config to Cisco Prime Infrastrcture (1.3.0.20)It fails and I cet this error i Prime: No device package found for the specified device.Any idea?-Tommy-
Hi,Anybody knows that the Cisco outdoor antennas (for example: ANT25137NP-R and ANT2544V4M-R) made of UV resistant polycarbonate?ThanksJanos
What is the best/most accurate way for collecting per AP data usage/volume? The AP could be either LWAP or Autonomous.Thanks.
Thats the question, any ideas?J.
Resolved! WebAuth Cert signed by CA on WLC
Hello guys,i have some Problems with IOS6 Device when using the WebAuth on WLC.I think that the Problem is that i have an self signed Cert on the WebAuth of the WLCs which is untrustworthy for the Safari.So i think the only solution is to install an ...
Resolved! Mesh network without WLC?
Hello,I searched internet and didn't get straight forward answer.... So - is this possible to build mesh network (max 2 hops) on AP 1602 without any controller (WLC)? I would be appreciated for answer.
I have a WLC4136 wireless controller with AP1020 access points.The wireless network runs fine.I have recently purchased an NEC P350W projector. It has network projecting capabilites. I have the projector wired into our network as it has a LAN portOn...
