Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Question on a AIR-ANT2410Y-R. Is there suppose to be a short between the Center core and the braid? Have one unit that has short have one unit that does not have short.
Hi there.We have a bunch of CAP 2702E access-points in combination with the AIR-ANT2524V4C-R external Antenna and WLC 2504In the instructions I found the flowing sentence: <<The 5-GHz antenna cables are identified by a orange collar nearthe connector...
Hallo, i am configure an SAP 2602i via GUI. But i can´t configure a new SSID for both Radios. I get an error, that the VLAN is not configured on the 5 GHZ Interface. But i activate both checkboxes in every VLAN.Can everyone tell me what i make wrong?...
Hello*Jan 10 13:21:00.311: %CAPWAP-3-ERRORLOG: Go join a capwap controller*Jan 10 13:21:00.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.1.1. 149 peer_port: 5246*Jan 10 13:21:00.415: %...
Dear Experts, We have configured ISE 1.2 in the distributed environment.so in the operation Authentication tab we are not getting any authentication logs.we have 1 admin node and aslo 1 PSN node and MN node.all the 3 nodes are up and synchronised wi...
Hi Everyone, We are replacing WLC from 2112 to 2504.I have GUI access to both.I need to copy config and settings from old to new one.I have config new WLC with all the settings like cdp,ntp,snmp etc.Is there any way that i can config or add 5 AP's w...
Can someone give me a simple explanation for why unique subnets would be necessary in a multi-site deployment when using WiSM?Are there any other situations other than WiSM where using unique subnets as opposed to a standardized scheme would be benef...
Dear gents,i have got 8 pieces of access point 4410nand i have a router 881 /k9 secI want to cover a building of 2 floors with this access pointswithout any cablesand i need to know how to make it ?what is the configuration ?
I am running a wireless network with about 130 AP's connected to a 8510 controller and using Prime for management. I am trying to get AP utilization for an AP that is no longer connected and when I try to run the report Prime reports that it cannot ...
Hey guys- We are currently running a Cisco WISM that manages roughly 500 AP's (1230) in Production today. The Wireless environment equipment is now going to be replaced with 2x8510's for Production, 2x5508's as Guest Anchor WLC's for Guests, and A...
So basically I came into an environment where my predecessor had no formal IT training and apparently learned to run before he learned to walk, so some of the stuff he set up “works”, but there are issues with it. For example, the WLC Controller that...
I have been looking at a WiSM farm and the main WLAN Profile across the entire farm shows the profile mapped to the management interface. A quick look at the list of clients, however, shows the clients all mapped to different VLANs configured on the...
I have a problem I get my wireless module is no longer open get just try 10.10.10.1, 2002 ... open does anyone know why?
I am in the process of deploying a whole bunch of Cisco AP to replace existing wireless infrastructure. I have configured FlesConnect groups as all the AP's will share a same config. Because there will be many AP's, I would like to preprovision the...
Hi Guys,I have a trouble to configure the CISCO radio Air sap 2602, I need make a link between 2 radios, but I can't use like a repeater, because I need use the ethernet port, can I put a radio like access point and another like a client? if yes, how...
