We have both DNS and Option 43 contorller discovery ways in one network but they direct to different WCL .I just want to know which one is more aggressive to advertise the IP address of controller. thank you in advance.
Dear SupportWe are deploying wireless with voice.we choose WLC 5508 and AP AIR-CAP3602E-X-K9 for indoor.For outdoor we chosse AIR-CAP1552SA-A-K9My question, is all these AP (indoor and outdoor) manage by the same controller 5508 ?Waiting for your qui...
guyz if i enabled managment frame protection (MFP) globally on all WLCs without having any clients supporting 802.11W would it actually make a difference in security or just better leave it disabled ???
I have noticed a lot of packet s are dropping in authenication process as we using certificate(third party) based autenticationSecurity we use L2 WPA+ WPA2 - AES - 802.X and pointing to IAS server.*dot1xMsgTask: Jun 25 10:54:47.600: %DOT1X-3-MAX_EAPO...
Guyz i have 8 WLCs and i read recently about the managment frame protection which is currently disabled globally and on the WLAN its enabled optionally for Client MFP althought i dont have any clients that support 802.11W , if i enabled MFP globally ...
Hi, im badrul..i got one problem regarding the wism module controller. as we know in wism module have 2 controller, controller 1 and controller 2. i try to configure that wism module. but only controller 1 can used. for controller 2, it not detect th...
Hi,I am trying to connect Cisco Aironet 1142 (which has been converted into Lightweight AP already) on WLC in Cisco Catalyst 3850. But i am getting following error when i console into LWAPP.Translating "CISCO-CAPWAP-CONTROLLER.CISCO-CAPWAP-CONTROLLE...
Hello,I got the following error via Mail from my NCS.Virtual Domain: ROOT-DOMAINNCS has detected one or more alarms of category AP and severity Critical in Virtual Domain ROOT-DOMAINfor the following items:1. Message: AP 'AP01' disassociated from Con...
hey everyone,for some reason our wlan-controllers were build up to be standalone instead of beeing one mobility-group.I would like to change this in order to use all features of HA.let me describe our scenario:two WLCs 5508 running SW ver. 6- same su...
On a stand-alone SAP 1602I-A-K9 access point, is it possible to only allow people to connect to the access point during certain hours of a day? For example: 8:00 am - 7:00 pm? If so, where is that setting located?
Hi All, I have just download the Auto-to-LWAPP upgrade tool and it is saying that it does not upgrade Air1261 from Auto-to-LWAPP, is it so? If yes, then what is the procedure to convert Air 1261 APs from Autonomous to LWAPP?Also, when I start the upg...
Good day,I have a questions. I am trying to setup a wireless hotspot using 1 x 2106 wlc and 2 x 3502e ap's. Before the 2106 could even recognize the APs I need to upgrade to the latest IOS. Now it can see the APs but the signal strength coming off of...
I've done a mistake in mapping the FlexConnect ACL with the VLAN in my AP's which are deployed as locally switching mode. I forgot to permit the WLC IP address in the ACL so that my AP cannot be registered to the WLC( so stupid, ain't I?). For now I ...
Its been a while since I deployed a bridge and need a refresher.If your power injector is powered on and connected to the network does it show on the switch as being up/up. I'm working remotely, supporting a client with a new bridge install and have ...
Hello Guys I hope you're ok.I'm here again try to find out what does mean backhaul I read this term but I don't get it what does it mean and what it does on Wireless network. I tried to use a translator and I didn't get a translation. Sorry bu I'm no...
