Hi, I need a solution that can isolate clients from each other on a Cisco Meraki MX64W model.So far I have found how to isolate clients from different VLANs. Maybe someone has managed to isolate clients from each other in separate VLANs?
Forum Posts
Hello, We have a handful of WLC 5520 units in our lab being prepared for deployment. We are just working on getting AireOS updated from 8.10.132.0 to 8.10.196.0 via the SP GUI, and getting this error: We noticed the same issue in this bug report: h...
We have a wireless network, created from Meraki CW9164i APs (Current version: MR 30.6). It advertises three SSIDs: Corporate, Guest and IoT on 2.4 and 5GHz. We do not (yet) run 6GHz, though that is our intent in the near future.In one area of the net...
Hi,I received a 9163E Access Point and with it being an outdoor model I expected the casing to be fully metal. I was surprised to see that the lid is plastic and after removing it states it is polycarbonate and weighs approximately 250g. Its stamped ...
All access points with MR 30.6 version do not show the splash page when clients connect, the solution is to downgrade to MR 29.7.1 version.This only happens if you are using splash page redirection.
Hi Folks, i have question regarding setting mobility tunnel between wlc 9800 and 8540, i need to anchor the guest network back to 9800 wlc. my concern is if i do that would that cause any issues given that the guest network on 9800 is configured unde...
I need to configure static IP on the BVI1 interface but the interface keeps resetting. I get the notification %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
Hello everyone, when I try to join the AP on the 9800 (17.12.4), I get the following message: Nov 16 07:39:12.187: %APMGR_TRACE_MESSAGE-6-WLC_APMGR_INFO: Chassis 1 R0/0: wncd: Info : - Qos not available for wlans 3, for AP KE-AP with AP MAC xxxx Does...
Resolved! Antenna parameters and gain in EWC
Some doubts about antenna gain and parameters in EWC. I can't understand why is so complicated: I have to check which antennas the AP are using (A, B, C, D) and the antenna gain in 0.5 dBi units. Cases:1. I connect an AP C9115AXE with 4 antennas ANT2...
1) I have 2 Ax150 how to prevent access to my main network from the guest network.2) how to put a static DNS as i put a static ip adresse to my ax 150
We have this WIFI setup using Google oAuth + Walled garden + Splash login as shown here: https://documentation.meraki.com/General_Administration/Cross-Platform_Content/Using_Google_OAuth_Splash_with_a_Walled_GardenIt works great but once the connecti...
Hello,Is there a best suggested software upgrade path from 17.6.4? As per the documentation, it is suggested to jump to 17.9.4, however the software manager on Cisco's website suggests that I use software version 17.12.3. I would prefer to use the ne...
Whilst distracted in my lab, I accidentally deleted the image in Part 1 and 2 leaving me with a U-Boot loop. Is there a way to push an image back into flash?
Hi everyone, We have a WLC connected to the CORE switch directly and I'm just wondering if it's required to configure DAI on the CORE switch, since all the users' traffic is tunneled to the WLC, I tried to check that in the configurations best practi...
We are having reports of our clients loosing connectivity to the network. Controller is a Cisco 9800-L APs are 9120AXE-B'sClient is a Zebra MC93 hand scannerClient auth is local WPA2-PSK connectionI have attempted to replicate the behaviour unsucces...
