I'm sorry, I'm a rookie. Could you please tell me how to solve the issue of my 9115 AP displaying "N/A" constantly? Thank you.
Forum Posts
Hello Team,In our infra we are using 3800 & 9130(whih were newly deployed) AP's. Users while roaming between the access points facing disconnection. for 9130 do we need to enable any specific settings for roaming? since both the access points are of ...
Hi Cisco Experts,We have a WLC : 9800-CL 17.3.6 + C9120AXI APs 1. 2x WLANs, both are in untrusted zone WLAN1: Staff , 802.1x (AD users) WLAN2: Guest, WPA2, and WebAuthentication (L3 consent, captive portal)2. They use the same Access Pol...
Resolved! Aironet 2800 USB Firmware Upgrade
Hello everyone,Is it possible to upgrade a Aironet 2802I via USB port? Thanks,Reece
Resolved! Configuration
Hello,Can anyone help the configuration of AIR AP 2802I-B-K9 ? please share me the pdf or video any one have .Thank you Satheesh
Resolved! SNMP OID for AP Radio Throughput
What is the WLC OID to collect the throughput per AP radio? I have been digging through the MIB tree for my WLC AIR-CT2504-5-K9 but haven't found it. The WLC Monitoring Dashboard shows this, but I need to collect it over SNMP.
Hey Gang, Here is a new one that we are troubleshooting. Maybe someone has ran in to this. We have a pair of 9800-80 WLCs running in HA that we have been slowly migrating to from our 8540s. The 9800 system is doing an HA switchover daily, sometimes t...
Hi c9800 wlc has guest ssid. Under the same WLC, we can see two guest State(Monitor---->Client) when user access the guest ssid. One is "Run" and second is "Web Auth Pending". What reason cause the second state? Thank you
I have been receiving these error messages while I'm trying to join a LWAP to the WLC. I tried running the command config ap cert-expiry-ignore mic enable on the WLC, but it won't work.WLC software version is 7.6.100.0.AP model AIR-CAP3502I-E-K9AP im...
Hi, We are currently using WLC AIR-CT2504-5-K9. It has reached end of support in April 2023. Therefore, we hope to replace model C9800-L-C-K9 instead of AIR-CT2504-5-K9. Now we have connected the AP models AIR-AP1832I-E-K9C and AIR-CAP1702I-E-K9. do ...
Hi All, Running fabric in a box on with wireless enabled, on a stack of Cisco Catalyst 9300 Series Switches (C9300L-48UXG-4X / C9300L-24P-4X). Need to upgrade the WLC version from 17.3.4 to 17.6.4 - Can this be done on the WLC only or does the stack ...
Hi all,I'm trying to connect new APs to WLC at a new location and the APs are joining and seconds later they are disconnecting from the WLC. When I consoled into one of the APs it's showing the output I have attached, below is part of what I'm seeing...
Hi All, Running 9800-40 WLC's Version 17.6.4 and DNAC Version 2.3.3.6-70045, would like to utilise the new AP "ZONES" feature via DNAC. What version of WLC code is supported? Any docs/advise would be helpful. Cheers,
Dears,I have a cisco 1852i as master mobility express and i have bought cisco 2802i.can cisco 2802i join as subordinate AP under 1852i ??????
We are currently using the AIR-CT2504-5-K9 wireless LAN controller (WLC), which reached its end of support in April 2023. Consequently, we are looking to replace it with the C9800-L-C-K9 model instead of the AIR-CT2504-5-K9. Currently, we have deploy...
