Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Cisco 1130AG Autonomous DHCP problems
I am having a problem getting DHCP to work for interface BVI1. I have tried everything I can think of and now am asking for the smarter peoples help. DHCP works great for the clients but BVI1 will not get a DHCP address no matter what I try. Below is...
Hi,I am wondering if it is possible to do MAC pre-authentication (MAC filtering) while also using LDAP for user authentication. For example, users who have their MAC in the MAC filter will be automatically allowed, which the remaining WLAN users will...
Hello,I have a problem with oeap600 .On my first scenario, I had 5508 with software 7.0.116. In this point, only one oeap600 was able to do join on WLC. Always, when I tried to set up the second oeap600, this second AP goes up and i...
Resolved! How to setup CCKM
Hi,We are rolling out 20+ APs (1042N-E-K9) and one of the VLANs is used for VoIP. We would like to enable CCKM, but are a little unsure of how to go about it after reading through many of all the documentation. We have successfully enabled one AP to ...
Resolved! Wi-Fi Authentication
Hello,I have a situation where I have inherited some old HP wireless access points (no change to Cisco coming anytime soon) and I need a way to force users to a landing page where they can input a common password before gaining acc...
Resolved! Radio problem on an AP1142N
Hello,I 've got a problem on an AP1142N. It joins correctly its controller (5508 WLC) but one of his radio (Dot11Radio1) won't go up : #show cdp interfaceDot11Radio1 is reset, line protocol is down Encapsulation ARPA Sending CDP packets every 60 se...
HI,I currently have a wireless mesh network that at all access points have an ethernet cable connecting to specific remote points (Kind of had to McGyver this setup). I am actually looking to see if it is possible, to use multiple SSID's, one for use...
Hi.I post this here as well, as in Security, becauese Im not realy sure that this is a ISE problem.I have a problem with a guestaccess using CWA on ISE 1.1.1 and WLC 7.2The setup is realy simple with redirect ACL to ISE and after that an permit-all A...
Hi Folks, We have a pair of WiSM modules in our Core switches and a pair of 5508's in our DMZ. We can successfully tunnel clients to the Anchor controllers in the DMZ when there's no AAA specified, however, when I add AAA servers for Authentication ...
Under high severity Alerts Its showing following ErrorAn exception occurred.Please check the AAD.log file for further details.AAD log shows This22-Oct-2012|10:48:17.625|ERROR|AAD|TP-Processor6|DeviceManager|getHighSeverityAlerts()|.|com.cisco.nm.trx....
Resolved! EPHONE 7921 PROBLEM WITH UC-560
I have a problem with 7921 phones registered with a UC-560.The problem is as follows:The phone works fine, but when you have an active call, the menu display disappears (hold-transfer) and you can not hold or transfer calls.The display only shows the...
Hi all,Wireless is working ok on 1811W.Need to know from command output below what values are considered good for power and signal strenghts1811w#sh dot11 associations all-clientAddress : 40fc.894e.c48c Name : NONEIP Addres...
Resolved! change floor height in WCS heatmap!
G'day guys,Just uploaded a map and placed AP's in it but put the wrong info for floor height as 7m instead of 4m. I tried to edit the floor area and changed it but apparently the heatmap still shows 7m even after i did a refresh from network. Is it p...
Hi All,In need of some help with two of these devices.We would like to use these as two basic access points, is this possible?I am unable to assign an IP address as i cannot use the configure terminal command as it does not exist?Do i need to use a w...
Deploy OVA template. Task was cancelled by user.
