Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Need FUS file for 3504 WLC
My WLC is stuck in bootloader mode, and only has the following options:1. Run primary image (Image not found)2. Run backup image (Image not found) - Active3. Change active boot image4. Clear configuration5. Manually update imagesNothing I do will wor...
Hi Community,I have a Cisco 3800 Series AP that has entered ROMMON mode and is currently showing the Uboot>>. I would like to install the IOS image 8.5.171, which matches the version running on my 2500 WLC (8.5.171).Could someone please guide me with...
Resolved! C9163E unistrut mounting
Hi,I have a Cisco 9163E AP with omni antennas installed. The AP will be mounted on the side of a warehouse and the survey advises having the AP away from the building using a unistrut arm rather than sit flush.Had anybody an examples of similar insta...
I have a device: CW9178I. How can I upgrade via TFTP or USB on the CW9178I, because in the CLI I don’t see TFTP or USB options?
Hi experts,Our system deploy SSID with WLC C9800 and ISE.We are having a problem. Please give me some advice.We have 5 separate zones. Different group IPs but same VLAN.Some users can use Wifi normally but when they move to another zone (roaming), th...
Resolved! SNMP query for Cisco WLC and AP
Query - When we configure the SNMP in the WLC, does that config gets pushed to the APs?
Hi Team,I have an WLC9800L install on VM..My AP 3802 is discovered into it and also SSID is broadcast but my end user is unable to connect with this SSID.Note: All devices like WLC9800L install on vm and AP in same vlan..and use will also get the IP ...
Resolved! WLC 9800 Feature ip-mac binding
Hi All I recently discovered that the WLC 17.9.1 offers in the Policy Profile an option to enable/disable IP MAC Binding, which is required for example when using VMware Workstation with a bridged Guest, so that both, the host and guest can get an IP...
I want to change APs that participate in EWC in CAPWAP mode to EWC mode.I was able to convert to CAPWAP⇒EWC, but some APs couldn't, and I noticed that the bin file for EWC was not installed.What can I do if my installation doesn't work?Run to factory...
Resolved! C9178i pendant mount
Good morning :Where can i find information on pendant mount materials /part no. for the Cisco 9178i - WIFI 7 AP
Resolved! Mounting bracket reuse
Have a customer that has a bunch of AIR-2802I access points and are going to be replacing them with new Catalyst 9166I AP. Will the new AP's use the same mounting brackets or will the brackets need to be changed out? thank you
I having and issue where I have APs configured with 4 WLANs within a hotel that some seems to stop associating client devices for one particular WLAN. Is not all the APs and just some and not always the same AP but the AP still has clients from the o...
Hi! I got stuck with the first exercise for connecting the laptop to the wireless router. I can see the IP address for the laptop. when I go to the desktop / pc wireless, it says I have succesfully connected to the access point. but when I try to se...
Hi all, I have a "not so common" setup Flexconnect design of multiple sites, one subnet each. On the HQ, WLC is in the local subnet aswell, but still using Flexconnect (for the ease of use). "Management over wireless" is enabled and is working from ...
Hello,I have a Cisco Catalyst 9300 configured as an Embedded Wireless Controller (EWC), running IOS-XE 17.15.3The APs (9115 and 1852) discover the controller, start the CAPWAP process, but fail to complete the join. In the logs I see CAPWAP/DTLS mess...
