Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello all, a few days ago (December 3rd) my wlc 9800-40 with sw 17.3.7 faced an issue where the active member and the standby switched over. I found the following logs about the event: Dec 3 15:19:07.495: %REDUNDANCY-3-STANDBY_LOST: Standby processo...
Dear All,I have configured a Mobility Group between a WLC 5508 with 8.5.176.2 IRCM, and a WLC 9800 with 17.9.4a.The mobility Group status is UP.But in the Mobility Peer Configuration, I see that the 9800 status is N/A is it a problem?Then I start to ...
Buenas, he seguido todos los pasos de este enlace para asociar el LDAP a nuestro WLC Cisco Serie 2500 (Módelo 2504) con v 8.5.171.0 para que los usuarios se autentifiquen con sus cuentas de dominio https://www.cisco.com/c/es_mx/support/docs/wireless-...
Hi all, I manage a school environment with 4 locations. Until last year, there was one Cisco 3504 and 20-30 1832 APs at each site. Then came a central vWLC to manage all 4 locations. This is installed on a HyperV at one of the 4 locations. With the m...
Hi allCould you please suggest, we are facing wireless client could not ping each other and we are using cisco wlc 9800 model integrate Cisco ISE 3.1.ThanksWith Regards,Shh
Hi team, Just want to ask, can we implement Wireless WLAN iPSK without ISE ? *like in the Meraki? I already search the documentation but seems like it need ISE to "seperate" the PSK and need to register the MAC Address of the client *i think it's no...
Hello Everyone,I have problem with AIR-CAP3702I-A-K9.My Switch is: C9200L-48T-4G, SW image: CAT9K_LITE_IOSXE, SW Version: 16.12.4. No Stack and PoE.WLC model: 5508, Software Version: 8.5.182.0Because this Sw doesn't have PoE, most of the PoE Injector...
Resolved! Cisco WLC 5508- Mobility tunnel creation
Hello All,In our current wireless setup, we already have an Anchor WLC (5508) which is mapped to the Foreign WLC (5508).I need to add a new Anchor WLC to the Foreign WLC. The Foreign WLC's are in HA pair. My question is, since the Foreign WLC's are i...
Resolved! DHCP Req Stuck
Hello,Today i got many client reporting that the wireless client can't connect to the wifi, and when i check in the WLC the client stuck on dhcp req state. If the client using static ip address, the client can connect to the network. The AP run in fl...
Resolved! Catalyst 9410 and Cisco Meraki Roaming
We are running Cisco Meraki APs that are connected to a Catalyst 9410 switch and are experiencing and issue with roaming. We put in the 9410 switch last week replacing a 4510. We did not have this issue when the same Meraki APs were connected to the ...
Hi,I got WLC 5520 running 8.10.190.0 and SSO.When I started my work today I got a message from Prime:Redundancy notification trap triggered by Controller '10.0.0.148' having Redundancy-Management IP '10.0.0.145', Local state is 'Active' and Peer Redu...
Resolved! WLC 9800 output header is repeated
Hello, i' m using terminal length 0show ap cdp neighbors but every 10 rows the header is repeated. Is there a way to stop this?
Hi, hoping someone can help with this type of setup below;I have a Cisco 3750 Switch that is used for distributing the Internet for people to connect in to.At the moment the setup is; Switch (in rack) > Patch panel to Ethernet Wall Ports > Laptops/ P...
Hello,i have setup a 2504 Controler for a WLAN on the Advanced Tab i configure a DHCP Server (i cant ping my DHCP/DNS Server)I even get an ipv6 address from the WLAN AP, but no ipv4 address and no DHCP / DNS from the LAN. Everything works on the LAN....
Hello community,I have a problem with 802.1x PEAP authentication.The environment is WLC 17.9.4 and ISE 2.4.APs are in local switching.When user tries to connect, I see request on ISE and then authentication times out.ISE says "5440 Endpoint abandon...
