I have a question about the 800 16 wireless LAN you can make you that both 2.4GHz and 5GHz on?
I have a question about the 800 16 wireless LAN you can make you that both 2.4GHz and 5GHz on?
Hello,I'm currently investigating on Aironet 2600 accesspoints.There are two model numbers, CAP2600 for controller based and SAP2600 for standalone/autonomous.My question now is, when I purchase a SAP2600 (=autonomous model), can I later convert it t...
HiWe have three SSID'sCORP SSIDGUEST SSIDMGMT SSIDI want to know ,Client wants the controller access from MGMT SSID where all the IT guys are sitting on their wirless laptop and at the same time they do not to get controller access for other SSID tha...
Running 7.0.220. There are several 'unknown' users every day reported in WCS. Investigating the connections on the WLC I find the clients are in a run state and passing traffic but there is no username listed on the client detail. (hence the unknown ...
Hi,Do the 1042 Autonomous APs support GRE tunnels?Any help is much appreciated.
Hello,I have a big problem. I have downgraded one of our AP1142N-E K9 to Autonomous mode with this image: c1140-k9w7-tar.152-2.JB.tarI have uses cisco's instructions.After successfull installation, I can open the Webinterface, but it shows almost no ...
I am trying to follow the Fips guide for the WLC5508 and it wants to encrypt the connection to the Radius, either with PSK key wrap or IPsec. I have the options for Ipsec only as the Windoes NPS does not support Key wrap from what a previous user con...
Hello,I had a problem with WCS report.Getting Cliente Associates to Wireless system (all controllers, all SSID´s), In the column IP address, I saw some IP´s out of my DHCP scope, however when I opened client details, the client IP address is correct ...
I have three Wireless LAN Controllers that are configured in the same Mobility Group. Two of the controllers have a the same WLAN (SSID) but the third doesn't. All three have other WLANs (SSIDs) that have the third controller as the anchor point for ...
Hello,I have a request for a wireless bride connection next to the Harbor.One AP on the top of a roof and two AP´s on moving waggons on a dock.I thought about a mesh connection with ethernet bridging.The question is:Will the radar on the ships interf...
Hi!Is it possible to use only 1 external antenna (AIR-ANT2524DB-R) with 1602E Access Point?Thank you for your suggestions!J
Hi there,I have APs confiugred as FlexConnect and each AP as a primary and secondary controller. I currently configured the APs on the primary controller. My question is whether I need to config the APs on the secondary controller with AP group, Flex...
Just doing some reading and had some questions that came up, if anyone could answer - I'd appreciate it.1. I do understand that once an LWAP joins a WLC, it remembers that WLC IP and always tries to connect to it - even after you clear the AP or the...
Hi, I'd like to configure lobby administrator defaults using Cisco WCS. The menu option I navigate to in WCS is Administration - Users - Lobby Admin - Lobby Ambassador Default (Tab).When setting the defaults I receive the message "WCS is currently se...
Hello,I'm deploying a virtual WLC environment with just one 1140 for test purposes.I'm trying to create a guest wlan but when I try to create the ingress interface it gives me a generic error.I guess that this error occurs because I just have one phy...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-16-2026 05:39 AM | ||
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM |
| User | Count |
|---|---|
| 5 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |