Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi,I have noticed when I was staging/priming the Cisco 1522, in the 802.11 b/g/n radio configuration, after setting the RF channel and TC power level to global and the Cisco 1522 reboots, the RF channel and TC power level reverts back to the default ...
Hi,Any help will be very welcome.I recently add a second CT5508 to the network, but when I tried to add the first 5508 to the mobilty group I received a message like this:"error in creating member"I've tried different mobility names, via GUI, via CLI...
hi guysI have a wap200 wireless access point configured and connected to the switch 2690 switch on vlan1, when I connect the wireless access points to the switch the port become disabled, is there a way to overcme this problem.thank you
Can i upload to a WLC a web auth page on PHP or what lenguajes are support on the WLC???Thanks!!!Regards
Any recommendations on a new tablet for air magnet survey. Sent from Cisco Technical Support iPad App
Hello Folks,I have a Cisco 1510 AP associated to a controller. When I issue the command config ap syslog specific x.x.x.x, the Controller CLI takes the syntax and sends the log messages to the syslog server. However this does not last. Usually within...
Due to an environmental contamination situation, we're replacing WiSMs with WiSM-2s along with their host 6500 chassis'.Will there be an easy way to port some or all of the existing WiSM configs to the new blades, or am I gonna have to rebuild everyt...
I currently have a WLAN (lets call it WIFI1) that is configured for HREAP local switching. All of my APs are running in HREAP mode as well. Is there any way to run one of these access point in local mode that users can still connect to WIFI1? I teste...
I'm trying to mesh a 1522 MAP through a 1042 RAP but this doen´t work. I get strange messages on the trap log:1 Mon Mar 26 18:40:19 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35...
Does anyone know what this means? disc_pak_classify: using policymap dir 1 sub-if Dot11Radio0/3/0 linktype 99?I can't find anything online. Thanks.
Hi.Aironet 1142, two units, using WPA Radius to IAS on Windows 2003. I have a problem with Macs beginning to surface. One laptop, OSX 10.6, ran fine for a couple of weeks. A problem started occurring, while using the network, communication will stop....
Hello all i configured my cisco AP 1140 using DHCP server so all users can access the internet, but i wanna assing an IP and join this AP to IP server where my DNS can control it..I enetered the express setting and did all basic steps (radio, secuirt...
Do wlan id's need to be same number accross all your WLCs on your network? If so is there a way to change them?thanks in advanceizzy
It's fuzzy, but I seem to recall reading somewhere that I can use the same public CA cert on all WLCs for guest WebAuth, assuming the following:All WLCs virtual IPs are 1.1.1.1FQDN abc.mycompany.com resolves to 1.1.1.1 in my DNS provided to guests by...
Hello,I am trying to bring the mobility group between 5508 wlc (dmz) and internal 5508 wlc but it says control and data path down. (Ihave allowed port 97 and ports 16666-16667 both ways)1. should the ntp be sinked inline iwth other controllers ?2. sh...
