Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
We are having a few problems with one of our WiSM controllers. The console is spammed with lots of fp_main_task: messages, an example is belowsshpmLoadSystemCerts: calling x509_alloc()*fp_main_task: Feb 01 11:36:49.862: sshpmLoadSystemCerts: calling ...
Can I use the same cert for 3 different controllers for this purpose? Each has the same virtual interface IP - 1.1.1.1. If I just assign each the same DNS hostname under the virtual interface, and then put that entry in our internal DNS resolving b...
Scenario: Latop clients want to make calls on wireless medium and QOS is enabled (WMM), how many voice call can take place simultaneously if some users sending data as well. What is the limit of successful voice calls without any problem in audio qua...
Hello all.I'm using a 5508 WLC with a couple of LAP3502 APs.The WLC itself is logging to a syslog server.I didn't configure anything on the individual APs, but still I see them announced at the syslog server.Now I'd like to disable AP syslogging: how...
Hi Folks,This evening I tried mocking up a design to create a VPN across our Corporate Network from the Outside Interface of a Cisco ASA 5505 (Remote Site) to the Inside Interface of an ASA 5510 (Local Site).However because I was trying to communicat...
We have just had a Mesh designed by an external company, and when we plugged it in we began have large numbers of mac-flap notification and more than 700mb of traffic sent across our data network.Our setup includes 2 5508 controllers and 9 152x APs3 ...
I am getting alerts on a daily basis for a rogue that is impersonating a valid access point, AP 'xxx' is being contained. This is due to rogue device spoofing or targeting AP 'xxx' BSSID on '802.11b/g' radio.Can anyone advise on if it's a false alar...
The environment:20 X air-ap1141N-A-K9 (these are standalone) in three different buildings with either 1 or 2 units per floor depending on sq. footage. IOS is c1140-k9w7-tar.124-25d.JA1.ProblemUsers running various tpyes of wireless cards on windows X...
We are looking to upgrade our 5508 wireless controller from 7.0.98.0 to 7.0.220.0. Reason being, we have experienced a lot of access points disassociating from the controller as well as client authentication issues. Has anyone upgraded from 7.0.98.0 ...
Hi,yesterday I asked if dipole antennas can be used on the 1262 stand alone APs. The answer is yes but, I was wondering specifically, if the 2.4 AIR-ANT2422DW-R= and the 5.8 AIR-ANT5135DW-R= are compatible with the 1262 AP?Thank you, Pat.
hi Experts,just a question regarding ACL configuration on the WLC. I am a bit confused on when to use CPU ACL and when should we apply the ACL on an interface?it seems CPU ACL is used to filter traffic processed by CPU, so normally used to prevent ac...
Hello,I'm doing some throughput calculation test between a wireless client and a wired desktop computer, and I'm a bit confused about the result i've got. According to the client's card and the WLC, the client is connected to 802.11g, at a speed of 5...
I just upgraded form a WRT 150N to an E4200 router. The main computer, a pc is attached to it with a wire. The other computers are wireless and laptops. The main computer runs windows 7. One laptop runs XP and the other vista. After the installation ...
Client has multiple 1240AG's setup as access points throughout their factory. They have a PC that they want to connect to the SSID and then be able to get to the Internet as well as the internal network. The PC has no problem connecting to the SSID...
Hi I have 2 x Redundant Guest Anchor Controllers (5508) located in 2 separate Data Centres with all the management and guest user VLAN spanned between two. Everything is working fine with the Guest WiFi access except the DHCP functionality as the Con...
