Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Has anyone tried using a 3500 CleanAir AP as a site survey tool? Could you set it up in multiple locations temporarily and gather interference data and analize through WCS? This would use the 3500 AP like you would the Spectrum Expert product.
Hi,I have implemented a Guest WLAN solution as per the recommended design from Cisco. We have two internal WiSM2 controllers providing services for Internal secure SSIDs. Both these controllers are members of a Mobility and RF management group.Two 55...
I coonfigured a 48 port Cisco 3560 PoE switch. I need to connect Access points to it. I connected them to the ports without any configuration.interface GigabitEthernet0/41!interface GigabitEthernet0/42!interface GigabitEthernet0/43!interface GigabitE...
Hello! I'm looking into purchasing a WAP4410N (possibly two) for deployment in the office. I have two main questions/concerns I would like to know if anyone can help me shed some light on.First, I see there are two variants available, the WAP4410N,...
Hello all,What is the maximum allowed number of wired clients behind a workgroup bridge? In other words, is there a limit on MAC addresses?I assume 1262 AP in WGB mode is connecting to a lighweight AP (1262 or 3502), latest IOS and WLC software. I wa...
I am preparing to set up guest wireless access in a dorm environment with a Cisco 5508 WLAN controller and Cisco 3602i APs. According to the book I've been reading, it recommends that I set up a WLAN for 802.11a/n clients in the 5 GHz range and anot...
Can please someone tell me what is the latest IOS for the AUTONOMOUS Cisco 1260 AP? Also where do you find this information? I serached the net and I found this version but I am not sure if this is the latest.12.4(25d)JA
dear friends, i have 4 wisms (8 controllers) installed on two distribution switches(6509) and 2 wisms on each chassis and both Distributions have VSL link to each other.i know in one mobility group we can have 24 controllersbut i want to know in this...
dear all, we have problem with an ap which makes unexpected reboots. find crashinfo attached. the following entry is striking. Unexpected execption to CPUvector 1100any idea?thanks in advance for your support!thomas
I am trying to reset this AP and the MODE button does not seem to be working. What steps do i need to take to reset the AP. It is an AIR-AP1200B-A-K9.
Hi Guys,If inter-VLAN communications is not required on a LAN, and clients at each VLAN just need outside (Internet) access, then do I still need to have a layer 3 device in my network? To be more specific, wireless VLANs are going to be created on a...
I have been upgrading my APs where I can to 3502s. Since these support MIMO, I was wondering if it benefited all my clients, or just the n clients. It seems to me that the client isn't involved in how MIMO works, so shouldn't all the clients benefi...
I want to purchase a new system comprised of 19 APs across a WAN consisting of 5 locations. I have a couple of questions. Is there any advantage of going with the 5500 series controller over the 4400 series? I want b, g and n coverage. Other than t...
dear friends,for 802.11a/n POE switch is working fine to provide power to the LAPs i know that.what about AIR-LAP1262N-E-K9 ? what is best switch to use for power of this LAPs POE or POE+ ???please advise about this if some one has tested it alrea...
Help! I've been troubleshooting a problem with TAC that I have had for a while now. Basically, any Apple device iPhone or iPad seems to connect to our WLANs but when the user opens Safari, a webpage will never load.The user is able to open the Emai...
