Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I want a voice deployment over wlan, i have wlc version 7.0.116.0. any advise or pdf file, or url regarding that?. post it.
Hi,We have 7921 and 7925 Wi-Fi phones. We have considered to configure multiple active network profiles with different SSIDs in these phones. However, we are not sure which SSID will be selected if APs advertise all of these SSIDs. Are the network pr...
Hi,I am implementing a wireless LAN, Data and Voice vlans are broadcasted via this WLAN, i am using a 5508 controller and a 1131b/g AP's.the problem is when i try to call any wireless phone from the IPPhone, the Wireless phone takes too long to show ...
Hello,we have two WISM Controllers running 6.0.196.4, a lot of 1252 APs and 100 7921 Phones with firmware 1.3.4(SR1). About 20-30% of the phones have the problem that from time to time (sometimes 3 times a day, sometimes after a period of 3-4 days an...
Hello,I have implemented a Voice over Wifi solution based on WLC 4404, AIR-LAP 1131G and CP-7921G. The Security mode deployed is WPA PSK. I have a random interruption on wireless access witch cause the CP 7921G to lose connectivity to the CUCM, even ...
AP: 3502,1141,1252Injector: air-pwrinj4WLC: wisms and 5508's 7.0.98.0WCSSwitches - 3750 (non-poe+)Trying to save my tech's time and gasoline (driving to remote sites) - Sometimes APs hang up, become unreachable - only way to get the AP working again ...
I am getting errors that state the following on WCS:"Access point 'APNAME' associated with controller 'CONTROLLER NAME' draws low power from Ethernet. Failure reason: 'The AP draws 15.4 watts from Ethernet'."I am using the 1250 series access points i...
the WLC 5508 is setupLAP1142 can join the WLCMy iphone4 can join the Wireless network andget IP 169.254.250.114sub mask 255.255.0.0but no gateway, no dnswhere can i assign ip range, gateway, dns for the mobile devices? thanks a lot.tony
Hi,WCS is reporting few AP's are not associated with it. While troubleshooting, AP conneceted switch interface shows UP/UP and show power inline output gives IEEE PD instead of AIR-LAP1131AG-E-K, after doing a shut/no shut on AP connected interface. ...
Hello, i'd like to force the speed/duplex of the integrated Gigabit interface on a LAP1042N, managed by a 4402 running software version 7.0.98 but I cannot find the command either by command line or on the GUI. Could someone help me? Many thanks! che...
Hi,I've been working with a client's integrated 3750 WLC running 4.0.179.11Manufacturer's Name.............................. Cisco Systems Inc.Product Name..................................... Cisco ControllerProduct Version.............................
We have a WCS running on Linux.The clock on the Linux box is correct, but the time on the WCS is not, as evidenced in reports of client associations and other reports.Where can I set - or even just check- the clock on the WCS? Thanks!Lynne
Hi,I have a WLC 5008 running with 40 AIR-LAP1042N-E-K9 and country code BE (Belgium) configured.I also have some AIR-AP1142N-C-K9 which I converted to CAPWAP OS.Unfortunattely only 1 of the 2 radio interfaces is working because of regulatory reasons....
Hello everybody,I'm having some problems to configure a WAP200 as repeater of an external access point WAP200E.I have followed all the steps to achieve it, but I can't get it to work:1. I configure WAP200 as repeater, locating the wireless MAC addres...
Hello-I recently purchased another 1142 AP to expand out our current wireless infrastructure, my question is, what exactly needs to be done for this to work so that users can roam freely and auto-connect to the closet AP with the best connection with...
