Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

HiI have a couple of 114n APs in my network and the CAPWAP uptime and AP uptime are almost the same. But there is one which always resets after some time. I have moved across to another switch port but the issue persists. I have other 1141 and 1131's...

grabonlee by Level 9
  • 4411 Views
  • 11 replies
  • 0 Helpful votes

      Hi, Some body can help-me about how can I store the file config.txt on Cisco aironet AP1231g  when the size of this file is more than 32kb (ex: 45kb long)?,  the size of the NVRAM is 32KB.      After I have had a error message of buffer size, i...

Dears ,I have upgraded my WLC from version 5.1.151 to version 6.0.202 and then to 7.0.116 .Since when , I see that all clients are disconnected every around 20 minutes and re-connected again .Does anyone has any clues ?WLC is 4402AP are AIR-LAP1231G-...

It seems that the only difference between the 1260 and the 3500 is the CleanAir capability. But what is the difference between the 1140 and the 1260? The only thing I can find is that the 1140 supports OfficeExtend. wIs there any hardware differences...

dhurshowy by Level 2
  • 9418 Views
  • 6 replies
  • 0 Helpful votes

I've read a lot and watched the recent webinar, but I still have a few questions:1) During and Event Driven RRM "The channel change is not random. It is picked  based on device       contention, thus it is an intelligent alternate choice.". Could you...

dhurshowy by Level 2
  • 1587 Views
  • 3 replies
  • 0 Helpful votes

We have a ssc ap that couldn't use H-reap mode, and all other ap already in H-reap. The Wlan we configured for enable H-REAP Local Switching and Learn Client IP Address, the problem is when user connected to this ssc ap, they will have intermittent i...

HiI am having difficulty upgrading the software code of WCS. We have a WLSE appliance that was upgraded to a WCS. I have downloaded the latest WCS software code (7.0.172) unto my PC. However, I do not know how to upgrade the WCS, since the WLSE is a ...

grabonlee by Level 9
  • 990 Views
  • 2 replies
  • 0 Helpful votes

HelloHas anyone been able to do this with a WLC, configuration guidlines say :""Wired guest access ports must be in the same Layer 2 network as the foreign controller."Anyone know if Cisco is working on making this solution work on L3 aswell ?Regards...

gudmundurk by Community Member
  • 887 Views
  • 2 replies
  • 0 Helpful votes

Hi allWhen I order the AP 1130 Series Eco Pack (AIR-LAP1131-EK9-10), do you know what I get?I assume this are included:- 10 1131 Access Points - Mounting KitI know that the power supply are not delivered with the 1140 Series Eco Pack. Is it the same ...

azeindler by Level 2
  • 2141 Views
  • 7 replies
  • 0 Helpful votes

Hello All -I am looking to get some more information on the iPad in the enterprise. We are currently using Cisco wireless running a corporate SSID using WPA+WPA2 with AES and 802.1X. Is anyone running iPad's in the 802.1X enterprise? We use a Device ...

Hi,In the WLC 2112, I can connect Access Points in the available port.For example:WLC Port 1 --> Connected to Switch (802.1Q)WLC Port 5 --> AP vlan 50 (access mode)WLC Port 6 --> AP vlan 50 (access mode)WLC Port 7 --> AP vlan 50 (access mode)Thanks

Review Cisco Networking for a $25 gift card